 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| RC SYSTEMS RC8660 VOICE SYNTHESIZER DoubleTalk RC8660 CMOS, 3.3 Volt / 5 Volt Voice Synthesizer Chipset GeneRal DeSCRipTiOn The RC8660 is a versatile voice and sound synthesizer, integrating a text-to-speech (TTS) processor, audio recording and playback, musical and sinusoidal tone generators, telephone dialer and A/D converter, into an easy to use chipset. Using a standard serial or eight bit bus interface, virtually any ASCII text can be streamed to the RC8660 for automatic conversion into speech by the TTS processor. The audio record and playback modes augment the TTS processor for applications requiring very high voice quality and a relatively small, fixed vocabulary, applications requiring special sounds or sound effects, and/or the recording of voice memos. The audio output is delivered in both analog and digital PCM audio formats, which can be used to drive a speaker or digital audio stream. The RC8660's integrated TTS processor incorporates RC Systems' DoubleTalkTM TTS technology, which is based on a unique voice concatenation technique using real human voice samples. The DoubleTalk TTS processor also gives the user unprecedented real-time control of the speech signal, including pitch, volume, tone, speed, expression, articulation, and so on. Up to 3.5 MB of nonvolatile memory is included in the RC8660 for the storage of up to 15 minutes of recorded messages and sound effects. A programmable "greeting" message can be stored that is automatically played whenever the RC8660 is powered up, allowing a custom message to be played or the RC8660's default settings to be reconfigured. A user-programmable dictionary allows the pronunciation of virtually any character string to be redefined, or even trigger the playback of tones, pre-recorded messages and sounds based on specific input patterns. All of these features can be programmed and updated via a standard serial port, even in the field after the RC8660 has been integrated into the end-product. The RC8660 is comprised of two surface-mounted devices. Both operate from a +3.3 V or +5 V supply and consume very little power. Most applications require only the addition of a lowpass filter/audio power amplifier to implement a fully functional system. RC8660 FunCTiOnal BlOCk DiaGRaM DoubleTalk RC8660 User's Manual Rev 1.2 Revised 10/22/04 (c) 2004 RC Systems, Incorporated RC SYSTEMS FeaTuReS * Integrated text-to-speech processor: - High voice quality, unlimited vocabulary - Converts any ASCII text into speech automatically - Capable of very high reading rates - Add/modify messages by simply editing a text file - On-the-fly control of speed, pitch, volume, etc. * On-chip recording, storage and playback of sound files: - Record to chip via microphone - Upload, download, and erase recordings and sound files, even in the field - Data logging mode allows analog quantities to be sampled and stored for later retrieval - Recording times from 130 sec to 15 min available * Tone generation: - Three voice musical - Dual sinusoidal - DTMF (Touch-Tone) dialer * On-chip A/D converter: - Four channels, 8-bit resolution - One-shot, continuous, single sweep, and continuous sweep modes of operation - Software and hardware triggering - Support for external op amp * Analog and digital audio outputs * Stop, pause, and resume controls * Serial and 8 bit bus interfaces * User programmable greeting and default settings * Flexible user exception dictionary: - Change the pronunciation of any input string based on spelling and context - Convert encrypted data into meaningful messages - Trigger tone generation, recorded message playback, voice parameter changes * In-circuit, field programmable * 8 KB input buffer for virtually no-overhead operation * Available in 3.3 V and 5 V versions * Low power (typ @ 3.3 V): - 6 mA active - 600 A idle - 100 nA standby RC8660 VOICE SYNTHESIZER appliCaTiOnS * Robotics * Talking OCR systems * ATM machines * Talking pagers and PDAs * GPS navigation systems * Vending and ticketing machines * Remote diagnostic reporting * Dial-up information systems * Handheld barcode readers * Electronic test and measurement * Security systems * Aids for the orally or visually disabled * Meeting federal ADA requirements RC8660 product Summary Part Number RC8660-1 RC86L60-1 RC86L60-2 RC86L60-3 Recording Capacity * 130 sec 130 sec 390 sec 910 sec Operating Voltage 5V 3.3 V 3.3 V 3.3 V * Based on 8 kHz sampling rate with ADPCM encoding RC SYSTEMS TypiCal appliCaTiOn CiRCuiT RC8660 VOICE SYNTHESIZER RC SYSTEMS RC8660 VOICE SYNTHESIZER Section 1: SpecificationS pinOuTS Figure 1.1. pin assignments RC SYSTEMS pin DeSCRipTiOnS Pin Name IC0 - IC32 Type INTPUT/ OUTPUT OUTPUT OUTPUT RC8660 VOICE SYNTHESIZER Name and Function CHIPSET INTERCONNECTS: Interconnections between the RC8660 and RC46xx chips. IC0 connects to IC0, IC1 to IC1, etc. IC30 - IC32 must have a 47 k - 100 k pullup resistor to VCC. No other connections should be made to these pins. ANALOG OUTPUT: Channels 0 and 1 digital to analog (D/A) converter outputs. The output voltage range is from 0 V to AVREF. AO1 is reserved for future use. TALK STATUS: Indicates whether a voice channel is active. TSn can be used to enable external devices such as a transmitter, telephone, or audio amplifier. The pins' polarity are programmable, and can be activated automatically or under program control. TS1 is reserved for future use. SUSPEND: Suspends audio output when Low, allowing playback to be paused. When High, playback resumes at the point output was suspended. These pins affect only the corresponding AO pin; they do not affect the digital audio DAOUT pin (use DARTS# to control DAOUT). During recording operations, SUSP0# will suspend recording when Low. SUSP1# is reserved for future use. Connect these pins to a High level if not used. AUDIO SYNC: Outputs a clock signal in synchronization with the updating of analog outputs AO0 and AO1. The pin changes state whenever the corresponding D/A converter is updated. During recording, AS0 changes state each time the A/D converter input is sampled. AS1 is reserved for future use. DIGITAL AUDIO OUTPUT: Provides the same 8 bit digital audio stream that is fed to the internal D/A converters. This pin can be programmed to be a CMOS or open-drain output. The communication protocol is progammable, and can operate in synchronous or asynchronous mode. DIGITAL AUDIO CLOCK: This pin is used to clock data out of the DAOUT pin and data into the DAIN pin in the synchronous digital audio output mode. DACLK can be programmed to transfer data on either the rising edge or falling edge of the clock. Connect this pin to a High level if not used. DIGITAL AUDIO CONTROL INPUT: This pin is used to control the operation of the DAOUT pin in a multichannel system. Reserved for a future product; connect this pin to a High level. DIGITAL AUDIO REQUEST TO SEND: A Low on this pin enables transmission from the DAOUT pin; a High suspends transmission. DARTS# may be used in both the synchronous and asynchronous transfer modes. Connect this pin to a Low level if not used. PERIPHERAL INPUT/OUTPUT BUS: Eight bit bidirectional peripheral bus. Data is input from a peripheral when PRD# is active. Status information is output when STS# is active. PIO0 - PIO7 also connect to the RC46xx chip. Text, data and commands can be sent to the RC8660 over this bus. STATUS: Controls the transfer of status information from the RC8660 to a peripheral. Status information is driven on the PIO0 - PIO7 pins when STS# is Low. STS# is active only when there is new status information. PERIPHERAL READ: Controls the transfer of data from a peripheral to the RC8660. Data is read from the PIO0 - PIO7 pins when PRD# is Low. PERIPHERAL WRITE: Controls the writing of peripheral data to the RC8660. Data on the PIO0 - PIO7 pins is latched in the RC8660 on the rising edge of PWR#. Sufficient time must be given for the RC8660 to process the data before writing additional data -- RDY# or Status Register bit SR.4 should be used for this purpose. Connect this pin to a High level if not used. READY: RDY# High indicates that the RC8660 is busy processing the last byte that was written over the Peripheral I/O Bus. Wait for RDY# to be Low before attempting to write more data. RDY# goes High briefly after each write operation over the PIO0 - PIO7 bus, acknowledging receipt of each byte. If the RC8660's input buffer becomes full as a result of the last write operation, RDY# will remain High until room becomes available. Note that RDY# can also be read from Status Register bit SR.4. A/D CONVERTER INPUTS: Analog to digital converter input pins. Analog signals sampled on these pins can be read through the serial interface, or stored in recording memory. Leave any unused pins unconnected. A/D CONVERTER TRIGGER: Starts A/D conversion when hardware triggering is selected. Minimum Low pulse width is 200 ns. Leave this pin unconnected if not used. AO0 AO1 TS0 TS1 SUSP0# SUSP1# INPUT AS0 AS1 DAOUT OUTPUT OUTPUT DACLK INPUT DAIN DARTS# INPUT INPUT PIO0 - PIO7 INPUT/ OUTPUT OUTPUT OUTPUT INPUT STS# PRD# PWR# RDY# OUTPUT AN0 - AN3 ADTRG INPUT INPUT Table 1.1. pin Descriptions RC SYSTEMS Pin Name AMPIN AMPOUT RXD TXD Type OUTPUT INPUT INPUT OUTPUT RC8660 VOICE SYNTHESIZER Name and Function A/D CONVERTER AMPLIFIER: Connecting an operational amplifier between these pins allows the input voltage to all four A/D converter input pins to be amplified with one operational amplifier. Leave these pins unconnected if not used. RECEIVE DATA: Asynchronous serial data input used to send text, data and commands to the RC8660. Connect this pin to a High level if not used. TRANSMIT DATA: Asynchronous serial data output used to read information out of the RC8660. This pin changes from a CMOS output to an N-channel open-drain output if any of the SEL pins are High, allowing multiple TXD pins to be wire-OR'd together in a multi-channel system. CLEAR TO SEND: The CTS# pin is Low when the RC8660 is able to accept data. If the input buffer becomes full as a result of the last byte received, CTS# will go High and remain High until room becomes available. BAUD RATE DETECT: BRD is used by the RC8660 to sample the host's serial data stream in order to determine its baud rate. BRD is normally connected to the RXD pin. The BRS0 - BRS3 pins affect the operation of BRD. Connect this pin to a High level if not used. BAUD RATE SELECT: Programs the asynchronous serial port's baud rate. Both the RXD and TXD pins are programmed to the baud rate set by these pins. Connecting BRS0 - BRS3 to a High level will allow the RC8660 to automatically detect the baud rate with the BRD pin. Connect these pins to a High level if not used. STANDBY/INIT: Dual function pin which either puts the RC8660 in Standby mode or initializes the RC8660's internal parameter memory. STBY# must be High on the rising edge of RESET#. Driving STBY# Low for 250 ms or longer causes the RC8660 to enter Standby mode. All peripheral and serial port handshake lines are driven to their false ("not ready") states, and the input buffer is cleared. During standby, the RC8660 draws the minimum possible current (100 nA typ @ 3.3 V), but it is not able to respond to any input pin except STBY# and RESET#. Returning STBY# High causes the RC8660 to enter Idle mode (600 A typ); the handshake lines are re-asserted and the RC8660 will be able to accept input again. If the RC8660 entered standby due to a Sleep Timer event, driving STBY# Low for 250 ns or longer then High will return the RC8660 to Idle mode. Driving STBY# Low for less than 250 ms initializes the RC8660's non-volatile parameter memory. The greeting message and user dictionary are erased, and all voice parameters and register settings are restored to their factory default settings. The audio recording memory is not affected. The RC8660 then announces its version number via the AO0 pin. Connect this pin to a High level if not used. CTS# BRD OUTPUT INPUT BRS0 - BRS3 STBY# INPUT INPUT SEL1 - SEL5 RESET# INPUT INPUT SELECT: Programs the channel pair that the RC8660 is to respond to in a multi-channel system. Connect these pins to a Low level in single-channel systems. RESET: A Low immediately terminates all activity and sets all pins to a predetermined state. During power-up, RESET# must be held Low a minimum of 1 ms after VCC has stabilized in the proper voltage range. All pins will be valid within 2 ms after reset. ANALOG CLEAR: A Low initializes the RC8660's D/A and A/D converters. Connect ACLR# to RESET#. CLOCK INPUT/OUTPUT: These pins connect to the internal clock generating circuit. All timing for the RC8660 and RC46xx chips are derived from this circuit. Connect a 7.3728 MHz crystal between XIN and XOUT. Alternatively, an external 7.3728 MHz square wave may be applied to XIN. POWER: +5 V 0.5 V, +3.3 V 0.3 V power supply connection. GROUND: Connect these pins to system ground. ANALOG POWER: Power supply input for the D/A and A/D converters. Connect this pin to VCC. ANALOG GROUND: Ground input for the D/A and A/D converters. Connect this pin to VSS. ANALOG REFERENCE VOLTAGE: Reference voltage for the D/A and A/D converters. Connect this pin to VCC. Caution: any noise present on this pin will appear on the AO pins and affect A/D converter accuracy. NO CONNECT: NC pins must remain unconnected. Connection of NC pins may result in component failure or incompatibility with future product enhancements. ACLR# XIN XOUT VCC VSS AVCC AVSS AVREF NC INPUT INPUT OUTPUT Table 1.1. pin Descriptions (Continued) RC SYSTEMS The RC8660 chipset includes a number of features that make it ideally suited for any design requiring voice output. The RC8660's major features are described below. RC8660 VOICE SYNTHESIZER Versatile i/O All data is sent to the RC8660 through its built in serial and/or parallel ports. For maximum flexibility, including infield product update capability, use of the serial port is recommended whenever possible. The RC8660's audio output is available in both analog and digital formats. The analog output should be used in applications where no further processing of the audio signal is required, such as driving a speaker or headphones (the output still needs to be filtered and amplified, however). The digital output is for applications that require further processing of the audio signal, such as digital mixing or creating sound files for later playback. FunCTiOnal DeSCRipTiOn Text-to-Speech Synthesizer The RC8660 provides text-to-speech conversion with its integrated DoubleTalkTM text-to-speech synthesizer. Any English text written to the RC8660 is automatically converted into speech. Commands can be embedded in the input stream to dynamically control the voice, even at the phoneme level (phonemes are the basic sound units of speech). A greeting message can be stored in the RC8660 that is automatically spoken immediately after the RC8660 is reset. Most any of the commands recognized by the RC8660 may be included as part of the greeting message, which can be used to set up custom default settings and/or play a pre-recorded message or tone sequence. An integrated nonvolatile memory area is also provided for storing a custom pronunciation dictionary, allowing the pronunciation of any character string to be redefined. ReCOMMenDeD COnneCTiOnS power/Ground Power and ground connections are made to multiple pins of the RC8660 and RC46xx chips. Every VCC pin must be connected to power, and every VSS pin must be connected to ground. To minimize noise, the analog and digital circuits in the RC8660 use separate power busses. These busses are brought out to separate pins and should be tied to the supply as close as possible. Make sure adequate decoupling is placed on the AVREF pin, as noise present on this pin will also appear on the AO output pins and affect A/D converter accuracy. In systems where the power supply is very quiet, AVREF can be connected directly to VCC. Designs incorporating a switching power supply, or supplies carrying heavy loads, may require filtering at the AVREF pin; a 150 series VCC resistor in combination with a 100 F capacitor to ground should suffice. Connect any unused input pins to an appropriate signal level (see Table 1.1). Leave any unused output pins and all NC pins unconnected. audio Recording and playback Up to 15 minutes of recorded messages and sound effects can be stored in the RC8660 for on-demand playback. Recordings are stored in on-chip nonvolatile memory, providing zero-power message storage. Additionally, the RC8660 can play eight-bit PCM and ADPCM audio in real time, such as speech and/or sound effects stored in an external memory or file system. Musical Tone Generator An integrated, three-voice musical tone generator is capable of generating up to three tones simultaneously over a four-octave range. Simple tones to attention-getting sounds can be easily created. Touch-Tone Generator Chip interconnects The RC8660 includes an integrated DTMF (Touch-Tone) generator. This is useful in telephony applications where standard DTMF tones are used to signal a remote receiver, modem, or access the public switched telephone network. Pins IC0 through IC32 and PIO0 through PIO7 must be connected between the RC8660 and RC46xx chips. IC30, IC31, and IC32 must have 47 k - 100 k pullup resistors to VCC. Sinusoidal Tone Generator Clock Generator A precision, dual sinusoidal tone generator can synthesize the tones often used in signaling applications. The tone frequencies can be independently set, allowing signals such as call-progress tones to be generated. The RC8660 has an internal oscillator and clock generator that can be controlled by an external 7.3728 MHz crystal, ceramic resonator, or external 7.3728 MHz clock source. If an external clock is used, connect it to the XIN pin and leave XOUT unconnected. See Figure 1.2 for recommended clock connections. analog-to-Digital Converter The four channel, 8-bit A/D converter can be used to monitor battery cell voltages, temperature, and other analog quantities. The ADC can be programmed on the fly to convert any single channel, or scan up to four channels repetitively. Data logging and audio recording to the RC8660's recording memory is also possible through the ADC. Figure 1.2. Clock Connections RC SYSTEMS inTeRFaCinG The RC8660 The RC8660 contains both asynchronous serial and 8 bit bus interfaces. All text, commands, tone generator data, real time audio data, etc., are transmitted to the RC8660 via one of these ports. For maximum flexibility, use of the serial port is recommended whenever possible. Not all RC8660 functions are supported through the bus interface. In particular, index markers, firmware updates, certain status information and A/D conversion are only supported through the serial interface. RC8660 VOICE SYNTHESIZER BRS3 L L L L L L L L H H H BRS2 L L L L H H H H L L L BRS1 L L H H L L H H L L H BRS0 L H L H L H L H L H L Baud Rate 300 600 1200 2400 4800 9600 19200 Auto-detect 38400 57600 115200 Auto-detect Serial interface The serial port operates with 8 data bits (LSB first), 1 or more stop bits, no parity, and any standard baud rate between 300 and 115200 bps. A typical RS-232C interface is shown in Figure 1.3. Note that the MAX232A transceiver is not required if the host system's serial port operates at logic levels compatible with the RC8660 (0/+5 V or 0/+3.3 V). The RC8660's serial port may be connected directly to the host system in this case. The CTS# pin should be used to control the flow of serial data to the RC8660. It is not necessary to check CTS# before transmitting every byte, however. All data is routed through a high speed 16-byte buffer within the RC8660 before being stored in the primary buffer. CTS# may be checked every eight bytes with no risk of data loss. All other settings Table 1.2. Baud Rate Options that there be at least one isolated "1" or "0" in the input character. The CR character, 0Dh, is recommended for locking the baud rate. The character is not otherwise processed by the RC8660; it is discarded. If the measured bit period is determined to be a valid baud rate, the RC8660 acknowledges lock acquisition by transmitting the ASCII character "l" (6Ch) on the TXD pin. The baud rate will remain locked unless changed with the baud rate command, or the RC8660 is reset. Baud rate selection The serial port's baud rate can be programmed using any of three methods: pin strapping, auto-detect, and by command. Pin strapping sets the baud rate according to the logic levels present on the BRS0 - BRS3 pins, as shown in Table 1.2. Auto-detect enables the serial port to automatically detect the baud rate of the incoming data. The baud rate command (described in Section 2) allows the baud rate to be changed at any time, effectively overriding the first two methods. The automatic baud rate detection mechanism is enabled when the BRS0 - BRS3 pins are all at a High logic level and the BRD pin is connected to the RXD pin. The baud rate is determined by the shortest High or Low period detected in the input stream. This period is assumed to be the bit rate of the incoming data; therefore it is important Figure 1.4. Baud Rate Detection Timing Figure 1.3. RS-232C interface RC SYSTEMS NOTE The measurement cycle ends when there have been no Highto-Low nor Low-to-High transitions on the BRD pin for 75 ms or longer. Consequently, the RC8660 will ignore any data sent to it for a period of 75 ms after the "lock-on" character has been received. The CTS# pin is driven High during this time, and the acknowledgment character is not transmitted until the RC8660 is actually ready to accept data. See Figure 1.4. RC8660 VOICE SYNTHESIZER Status messages Real-time status information is provided via the TXD pin. Status are transmitted as one-byte messages, shown in Table 1.3. Each message correlates to a status flag in the Status Register, shown in Table 1.5. The specific character used, and whether it will be transmitted, are functions of the V86 and STM bits in the Protocol Options Register. (The Protocol Options Register is described in Section 2.) For information about how to obtain reading-progress status, see the Index Marker command description. Figure 1.5. Multi-Channel System SEL5 L L L L . . H H SEL4 L L L L . . H H SEL3 L L L L . . H H SEL2 L L H H . . H H SEL1 L H L H . . L H Channel Pair All 2-3 4-5 6-7 . . 60-61 Disabled Activation Code - C2h C4h C6h . . FCh - Event Output has started Output has stopped Buffer almost empty (<100 bytes remaining) Buffer almost full (<100 bytes available) Standby mode confirmation Baud rate lock confirmation V86 = 0 V86 = 1 "B" "E" - - "S" "L" "s" "t" "e" "f" "p" "l" Requires STM = 1 Yes Yes Yes Yes No No Table 1.4. RC8660 Channel addressing Table 1.3. Status Messages Multi-channel system Multiple RC8660s can be connected in a multi-channel configuration by wiring the RXD pins together and TXD pins together, as shown in Figure 1.5. All communication is performed over the resulting RXD/ TXD bus. Individual RC8660s are addressed through a simple addressing scheme, shown in Table 1.4. Single-channel systems should have all of the RC8660's SEL pins connected to a Low logic level. This permanently activates the RC8660 so that no activation code is required, and configures the TXD pin as a CMOS output. Note that if any of the SEL pins are connected to a High logic level, the TXD output pin will be automatically configured to be an open-drain, N-channel output. NOTE Table 1.4 refers to channel pairs, because each RC8660 can potentially support two channels (AO0 and AO1). This feature may be implemented in a future version of the RC8660. Each RC8660's address is programmed through the strapping of its SEL pins; the logic levels present on these pins determine which activation code each RC8660 will respond to. When an RC8660 sees its activation code on the RXD bus, it becomes enabled and functions normally. All other RC8660s on the bus disable themselves at the same time, although the contents of their input buffers will not be affected. The 8 KB buffer within each RC8660 allows a channel to be opened, accept messages (text and commands), then be immediately closed -- thereby allowing another channel to be opened -- while the first RC8660 processes the information it just received. To address a specific RC8660, issue the appropriate activation code. For example, to address channel 4, transmit C4h. All subsequent output will be accepted by the RC8660 configured for channel 4, and ignored by all the others. Handshaking with each RC8660 in a multi-channel system is simplified through a special interrogation mechanism. Instead of monitoring each channel's CTS# pin, any channel can instead be queried by transmitting code C0h. In response, the active channel will return an eight bit status code on the TXD bus, as defined in Table 1.5. The Ready status bit should be checked at least every 8 data bytes in order to avoid data loss. RC SYSTEMS Bus/printer interface The RC8660's bus interface allows the RC8660 to be connected to a microprocessor or microcontroller in the same manner as a static RAM or I/O device, as shown in Figure 1.7. The microprocessor controls all transactions with the RC8660 over the system data bus using the RD and WR# signals. RD controls the reading of the RC8660's Status Register; WR# controls the transfer of data into the RC8660. The Status Register bits and their definitions are shown in Table 1.5. A registered bus transceiver is required for communication between the RC8660 and microprocessor; two 74HC374s placed back to back may be substituted for the 74HC652 shown in the figure. Prior to each write operation to the RC8660, the host processor should verify that the RC8660 is ready by testing the RDY status flag. The RC8660 can also be interfaced to a PC's printer port as shown in Figure 1.7. A 74HC374 can be used in place of the 74HC652, since bidirectional communication is not necessary. Handshaking is performed automatically via the BUSY pin. Because the RC8660 can take up to 15 s to accept data written to it (AC Characteristics, tYHWH parameter), software drivers should wait for RDY to drop to 0 after a byte is written in order to avoid overwriting it with the next data byte. Not doing so could result in the loss of data. Waiting for RDY to drop to 0 ensures that RDY will not falsely show that the RC8660 is ready the next time the driver is called. If a system interrupt can occur while waiting for RDY to become 0, or if RDY cannot otherwise be checked at least once every 8 s, a software timeout should be enforced to avoid hanging up in the wait loop. The time RDY stays 0 is relatively short (8 s min.) and can be missed if the loop is interrupted. The timeout should be at least 15 s, which is the maximum time for RDY to drop to 0 after writing a byte of data. In non time-critical applications, the output routine could simply delay 15 s or longer before exiting, without checking for RDY = 0 at all. Figure 1.6 illustrates the recommended method of writing data to the RC8660's bus interface. This method should be used for writing all types of data, including text, commands, tone generator and real time audio data. RC8660 VOICE SYNTHESIZER Figure 1.6. Recommended Method of Writing Data Via the Bus interface 0 RC SYSTEMS R 7 TS 6 Status Register Bit SR.7 = RESERVED (R) SR.6 = TALK STATUS (TS) 1 = Talking 0 = Idle SR.5 = RESERVED (R) SR.4 = READY STATUS (RDY) 1 = Ready 0 = Busy SR.3 = ALMOST FULL (AF) 1 = Buffer almost full 0 = Buffer not almost full SR.2 = ALMOST EMPTY (AE) 1 = Buffer almost empty 0 = Buffer not almost empty SR.1 = STANDBY MODE (STBY) 1 = RC8660 is in Standby mode 0 = RC8660 not in Standby mode SR.0 = RESERVED (R) R 5 RDY 4 RC8660 VOICE SYNTHESIZER AF 3 AE 2 Description Reserved for future use. Mask when polling the Status Register. The TS bit has the same meaning as the TS0 pin. "1" means that the RC8660 is producing output; "0" means output has ceased. The TS bit is not affected by the TS Pin Control command, which affects only the TS pins. Reserved for future use. Mask when polling the Status Register. The RDY bit has the same meaning as the RDY# pin. The RC8660 sets RDY to "1" to indicate that it is ready to receive data. RDY drops to "0" momentarily after each write operation over the PIO bus, acknowledging receipt of each character. This bit is "1" anytime there are less than 100 bytes available in the input buffer. AF is always "0" in the real time audio playback mode and when using the musical tone generator. This bit is "1" anytime there are less than 100 bytes remaining in the input buffer. AE is always "1" in the real time audio playback mode and when using the musical tone generator. This bit is "1" when the RC8660 has entered Standby mode. Standby mode is entered either by setting the STBY# pin Low or by allowing the Sleep Timer to expire. Reserved for future use. Mask when polling the Status Register. STBY 1 R 0 Table 1.5. Bus interface Status Register Bit Definitions Figure 1.7. Bus/printer interface RC SYSTEMS RC8660 VOICE SYNTHESIZER Figure 1.8. Method of Capturing Status information for Driving external Circuitry analog audio Output The analog output pins AO0 and AO1 are high impedance (10 k typical) outputs from the RC8660's internal D/A converters. When using these outputs, the addition of an external low-pass filter is highly recommended. When laying out the printed circuit board, avoid running digital lines near the AO lines in order to minimize induced noise in the audio path. If space permits, run a guard ground next to the AO traces. The circuit shown in Figure 1.9 is a low-pass filter/power amplifier capable of delivering 1.1 W to an 8 load, when operating from a +5 V power supply (power output will be less when operating from +3.3 V). The amplifier's shutdown pin can be controlled by the RC8660's TS0 pin to minimize current drain when the RC8660 is inactive. Digital audio Output The digital audio pin DAOUT outputs the RC8660's audio signal as a digital audio stream consisting of 8 data bits per sample. The normalized sampling rate for all text to speech modes, sinusoidal generator, and DTMF generator is 84 kbs (10,500 bytes/sec). The prerecorded and real time audio playback mode rates are user programmable, so their normalized rates will vary. See the Pin Descriptions and Audio Control Register command description for further details. Figure 1.9. 3 khz low-pass Filter/power amplifier RC SYSTEMS eleCTRiCal SpeCiFiCaTiOnS RC8660 VOICE SYNTHESIZER Figure 1.10. Test Circuit Supply voltage, VCC and AVCC . . . . . . . . . . . . . . .- 0.3 V to +6.5 V DC input voltage, VI . . . . . . . . . . . . . . . . . . . - 0.3 V to VCC +0.3 V Operating temperature, TA . . . . . . . . . . . . . . . . . . . 0 C to +70 C Storage temperature, TS . . . . . . . . . . . . . . . . . . - 55 C to +125 C aBSOluTe MaxiMuM RaTinGS* * WARNING: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; operation of the device at any condition above those indicated in the operational sections of these specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RC SYSTEMS DC ChaRaCTeRiSTiCS Symbol VIL VIH VIA VHYR VOL VOH IIL RO ICC RC8660 VOICE SYNTHESIZER TA = 0 C to +70 C, VCC = AVCC = AVREF = 3.3 V / 5 V, VSS = AVSS = 0 V, XIN = 7.3728 MHz Parameter Input voltage, Low Input voltage, High Analog input voltage (AN0-3) Input hysterisis, RESET# Output voltage, Low Output voltage, High Input load current Analog output resistance (AO0, AO1) Supply current Active Idle Standby Program (Note 1) 1 3.3 0.3 V Min - 0.3 0.7VCC - 0.3 0.2 Typ Max 0.2VCC VCC + 0.3 AVREF 1.8 0.5 VCC - 0.5 4 4 10 20 4 VCC - 0.5 Min - 0.3 0.7VCC - 0.3 0.2 5 V 0.5 V Typ Max 0.2VCC VCC + 0.3 AVREF 1.8 0.5 Unit V V V V V V Test Conditions IOL = 1 mA IOH = - 1 mA VIN = VSS to VCC 5 10 20 A k 6 0.6 0.1 18 1.5 15 35 13 1.2 0.2 33 2.5 20 65 mA mA A mA All outputs open; all inputs = VCC or VSS; AVCC and AVREF currents included Applies during internal programming operations: greeting message, dictionary, sound library and microcode updates. TA = 0 C to +70 C, VCC = AVCC = AVREF = 3.3 V / 5 V, VSS = AVSS = 0 V aC ChaRaCTeRiSTiCS External Clock Input Timing Symbol fC tWCL tWCH tCR tCF Parameter External clock input frequency External clock input Low pulse width External clock input High pulse width External clock rise time External clock fall time 3.3 0.3 V Min 7.2991 60 60 Nom 7.3728 67.8 67.8 18 18 Max 7.4465 Min 7.2991 40 40 5 V 0.5 V Nom 7.3728 67.8 67.8 15 15 Max 7.4465 Unit MHz ns ns ns ns Figure 1.11. external Clock Waveform RC SYSTEMS Bus Interface Timing Symbol tWSL tDVSL tDHSH tWRL tDVRH tDHRH tWWL tDVWH tDHWH tYHWH tWYH 1 RC8660 VOICE SYNTHESIZER Parameter STS# pulse width Low STS# Low to data valid Data hold from STS# going High PRD# pulse width Low Data setup to PRD# going High Data hold from PRD# going High PWR# pulse width Low Data setup to PWR# going High Data hold from PWR# going High RDY# High from PWR# going High (Note 1) RDY# pulse width High (Note 1) 3.3 0.3 V Min 215 155 5 215 85 0 380 -2 15 15 8 Max 5 V 0.5 V Min 250 150 5 250 40 0 250 -2 15 15 8 Max Unit ns ns ns ns ns ns ns s s s s Applies to the RDY# pin and RDY status flag. Figure 1.12. Bus interface Waveforms RC SYSTEMS Analog Audio Timing RC8660 VOICE SYNTHESIZER Figure 1.13. analog audio Waveforms Digital Audio Timing Symbol tCYC tWCL tWCH tDVCL tDHCL fS DACLK cycle time DACLK pulse width Low DACLK pulse width High DACLK Low to data valid Data hold from DACLK going Low TTS and DTMF generator internal sampling rate Parameter Min 200 100 100 80 0 10.5 10.5 Max Unit ns ns ns ns ns kHz Nominal Notes Figure 1.14. Digital audio Waveforms RC SYSTEMS Standby Timing Symbol tWSBL STBY# pulse width Low To enter Standby mode To reinitialize parameter memory To exit Standby mode (Sleep Timer invoked; Note 1) 1 RC8660 VOICE SYNTHESIZER Parameter 3.3 0.3 V Min 250 8 380 Max 5 V 0.5 V Min 250 8 250 Max Unit 250 250 ms ms ns Monitor handshake lines to determine when Standby mode has terminated. Figure 1.15. Standby Waveform Reset Timing Symbol tWRS Parameter RESET# pulse width Low After power on / VCC stable During operation tDRR RESET# recovery delay 1 3 2 ms s ms Hold RESET# Low during power-up Min Max Unit Notes Figure 1.16. Reset Waveform RC SYSTEMS paCkaGe inFORMaTiOn RC8660 VOICE SYNTHESIZER 100 pin plastic 14 x 20 mm QFp (measured in millimeters) RC SYSTEMS RC8660 VOICE SYNTHESIZER 48 pin plastic 12 x 20 mm TSOp (measured in millimeters) Recommended pCB layouts (measured in millimeters) RC SYSTEMS ORDeRinG inFORMaTiOn RC8660 VOICE SYNTHESIZER The RC8660 is available in several recording capacities and voltage ranges. The ordering part number is formed by combining several fields, as indicated below. Refer to the "Valid Combinations" table, which lists the configurations that are planned to be supported in volume. All configurations include the RC8660FP chip; the companion chip is shown in parentheses. For example, the RC86L60-1, a 3.3 V part with 130 seconds of recording memory, is composed of the RC8660FP and RC46L51FP. 0 RC SYSTEMS RC8660 VOICE SYNTHESIZER Section 2: principleS of operation The RC8660 has five primary operating modes and two inactive modes designed to achieve maximum functionality and flexibility while consuming the least possible amount of power. The operating mode can be changed at any time by issuing the appropriate command. NOTE The RC8660 will not begin speaking nor execute commands issued it until it receives a CR (ASCII 13) or NUL (ASCII 00) character -- this ensures that a complete contextual analysis can be performed on the input text. If it is not possible for the application to send a CR or NUL, use the Timeout Delay command. The RC8660 does not make any distinction between uppercase and lowercase characters. All data sent to the RC8660 is buffered in an internal 8 KB input buffer, allowing additional text and commands to be queued even while the RC8660 is producing output. Text-To-Speech mode. By default, all text sent to the RC8660 is automatically translated into speech by the integrated DoubleTalk TTS engine. TTS mode can be further subdivided into three translation modes: Text, which reads text normally; Character, which reads (spells) one character at a time; and Phoneme, which allows the TTS engine's phonemes to be directly accessed. Recorder mode. Any of the RC8660's four ADC inputs can be used to make audio recordings, such as voice memos. Analog voltages, such as from a temperature transducer or battery, can be sampled and recorded using the ADC's one-shot mode. All recordings can be retrieved via the serial port or played back on demand. Recorded Audio Playback mode. This mode allows messages and sound effects that have been recorded or downloaded into the RC8660 to be played back on demand. PCM and ADPCM data types are supported. Real Time Audio Playback mode. Data sent to the RC8660 is written directly to the RC8660's audio buffer. This results in a high data rate, but provides the capability of producing the highest quality speech, as well as sound effects. PCM and ADPCM data types are supported. Tone Generator modes. These modes activate the RC8660's musical tone generator, sinusoidal generator, or DTMF generator. They can be used to generate audible prompts, music, signaling tones, dial a telephone, etc. Idle mode. To help conserve power in battery-powered systems, the RC8660 automatically enters a reduced-power state whenever it is inactive. Data can still be read and written to the RC8660 while in this mode. Current draw is typically 600 A @ 3.3 V. Standby mode. This mode powers down the RC8660, where current draw is typically only 100 nA. Standby mode can be invoked from either the STBY# pin or with the Sleep command. Data cannot be read from nor written to the RC8660 in this mode. OpeRaTinG MODeS The RC8660 commands provide a simple yet flexible means of controlling the RC8660 under software control. They can be used to vary voice attributes, such as the volume or pitch, to suit the requirements of a particular application or listener's preferences. Commands are also used to change operating modes. Commands can be freely intermixed with text that is to be spoken -- allowing the voice to be dynamically controlled -- or to dynamically change operating modes, such as generating tones or playing recorded messages in the middle of a passage of text. Commands affect only the data that follows them in the data stream. All RC8660 commands are composed of the command character (CTRL+A by default), a parameter n comprised of an ASCII number string, and a single string literal that uniquely identifies the command. Some commands simply enable or disable a feature of the RC8660 and do not require a parameter. The general command format is: COMManD SynTax The Command Character The default RC8660 command character is CTRL+A (ASCII code 01). The command character itself can be spoken by the RC8660 by sending it twice in a row: CTRL+A CTRL+A. This special command allows the command character to be spoken without affecting the operation of the RC8660, and without having to change to another command character and then back again. Changing the command character The command character can be changed to another control character (ASCII 01-26) by sending the current command character, followed by the new character. To change the command character to CTRL+D, for example, issue the command CTRL+A CTRL+D. To change it back, issue the command CTRL+D CTRL+A. It's generally a good idea to change the command character if the text to be read contains characters which may otherwise be interpreted as command characters (and hence commands). The command character can be unconditionally reset to CTRL+A by sending CTRL+^ (ASCII 30) to the RC8660. Command parameters Command parameters are composed of ASCII number strings. The RC8660 supports two types of parameters: absolute and relative. Absolute parameters explicitly specify a parameter's new value, such as 9S or 3B. Relative parameters specify a displacement from a parameter's current value, not the actual new value itself. RC SYSTEMS Relative parameters allow you to specify a desired change in a parameter's value. For example, the Volume command +2V increases the volume level by two (V+2V). If the current volume is 4, the volume will increase to 6 after the command has executed. The command - 2V will have a similar effect, except the volume will be decreased by two. When operating on an RC8660 register (Punctuation Filter, Protocol Options, Audio Control and ADC Control), relative parameters allow you to set ("+") and clear ("-") individual register bits. For example, +65G sets bits POR.0 and POR.6; - 16$ clears ADR.4. If the value of a parameter falls outside the command's range, the value will either wrap around or saturate, depending on the setting of the SAT bit of the Protocol Options Register. For example, if parameters are programmed to wrap, the current volume is 7 and the command +4V is issued, the resultant volume will be (7 + 4) - 10 = 1, since the volume range is 0-9. If parameters are programmed to saturate, the resultant volume would be 9 instead. When writing application programs for the RC8660, it is recommended that relative parameters be used for temporarily changing voice attributes (such as raising the pitch of a word), using absolute-parameter commands only once in the program's initialization routine. This way, if the base value of an attribute needs to be changed, it only needs to be changed in the initialization routine. RC8660 VOICE SYNTHESIZER foreign words may require a bit more creativity, so that "Sean" becomes "Shon," and "chauffeur" becomes "show fur." Heteronyms (words with identical spelling but different meanings and pronunciations) can also be modified using this technique. For example, if the word read is to be pronounced "reed" instead of "red," it can simply be respelled as "reed." Text Mode/Delay (T/nT) This command places the RC8660 in the Text operating mode. The optional delay parameter n is used to create a variable pause between words. The shortest, and default delay of 0, is used for normal speech. For users not accustomed to synthetic speech, the synthesizer's intelligibility may be improved by introducing a delay. The longest delay that can be specified is 15. If the delay parameter is omitted, the last set value will be used and the exception dictionary will be disabled. This feature is useful for returning from another operating mode or disabling the exception dictionary (see Enable Exception Dictionary command). Character Mode/Delay (C/nC) Using the TTS synthesizer couldn't be simpler: simply write the text to be read to the RC8660; the RC8660 does the rest. The RC8660 also includes a number of software commands that allow you to modify the behavior of the TTS synthesizer, as described in this section. TTS SynTheSizeR This command puts the RC8660 in the Character operating mode. The optional delay parameter n is used to create a variable pause between characters. Values between 0 (the default) and 15 provide pauses from shortest to longest, respectively. Values between 16 and 31 provide the same range of pauses, but control characters will not be spoken. If the delay parameter is omitted, the last set value will be used and the exception dictionary will be disabled. phoneme Mode (D) This command disables the text-to-phonetics translator, allowing the RC8660's phonemes to be accessed directly. Table 2.1 lists the phonemes that can be produced by the RC8660. When concatenating two or more phonemes, each phoneme must be delimited by a space. For example, the word "computer" would be represented phonetically as k ax m p yy uw dx er Translation accuracy Because the RC8660 must handle the highly irregular spelling system of English, as well as proper names, acronyms, technical terms, and borrowed foreign words, there inevitably will be words that it will mispronounce. If a word is mispronounced, there are three techniques for correcting it: 1. Spell the word phonetically for the desired pronunciation. 2. Redefine the way the word should be pronounced by creating an exception for it in the RC8660's exception dictionary. This method allows words to be corrected without having to modify the original text, and it automatically corrects all instances of the word. Exception dictionaries are covered in detail in Section 3. 3. Use the RC8660's Phoneme mode. The first technique is the easiest way to fine tune word pronunciations -- by tricking the RC8660 into the desired pronunciation. Among the more commonly mispronounced words are compound words (baseball), proper names (Sean), and foreign loan words (chauffeur). Compound words can usually be corrected by separating the two words with a space, so that "baseball" becomes "base ball." Proper names and Phoneme attribute tokens The RC8660 supports seven phoneme attribute tokens that can be used in addition to the standard commands. These tokens do not require the command character or any parameters, but they can only be used in Phoneme mode and exception dictionaries. In addition, changes made to parameters with attribute tokens are only temporary. Table 2.2 lists these tokens and their equivalent "standard" commands. Applications of Phoneme mode Phoneme mode is useful for creating customized speech, when the normal text-to-speech modes are inappropriate for producing the desired voice effect. For example, Phoneme mode should be used to change the stress or emphasis of specific words in a phrase. This is because Phoneme mode allows voice attributes to be modified on phoneme boundaries within each word, whereas Text mode allows changes only at word boundaries. This is illustrated in the following examples. RC SYSTEMS CTRL+A "d" CTRL+A "m" "//h aw +<\\yy uw s p \iy k t uw t -\w ey .+/" -/d>/eh r \m iy dh ae RC8660 VOICE SYNTHESIZER Symbol nn / \ + - > < Function Set pitch to `nn' (0-99) Increase pitch m steps * Decrease pitch m steps * Increase speed 1 step Decrease speed 1 step Increase volume 1 step Decrease volume 1 step Equiv Cmd nP + mP - mP + 1S - 1S + 1V - 1V Note that Expression is disabled in this example, since the pitch variations due to the internal intonation algorithms would otherwise interfere with the pitch tokens. Compare this with the same phrase produced in Text mode with Expression enabled: CTRL+A "t" CTRL+A "e" "How dare you speak to me that way!" Phoneme mode is also useful in applications that provide their own text-to-phoneme translation, such as the front end of a custom textto-speech system. * Step size determined by nE command; m @ 2n Table 2.2. phoneme attribute Tokens Phoneme Symbol A AA AE AH AW AX AY B CH D DH DX E EH EI ER EW EY F G H I IH IX IY J K KX L Example Word das (Spanish) cot cat cut cow bottom bite bib church did either city ser (Spanish) bet mesa (Spanish) bird acteur (French) bake fee gag he libro (Spanish) bit rabbit beet age cute ski long Phoneme Symbol M N NG NY O OW OY P PX R RR S SH T TH TX U UH UW V W WH Y YY Z ZH space , . Example Word me new rung nino (Spanish) no (Spanish) boat boy pop spot ring tres (Spanish) sell shell tin thin stick uno (Spanish) book boot valve we when mayo (Spanish) you zoo vision variable pause * medium pause long pause Speed (nS) The synthesizer's speech rate can be adjusted with this command, from 0S (slowest) through 13S (fastest). The default rate is 5S. Voice (nO) The text-to-speech synthesizer has 11 standard voices and a number of individual voice parameter controls that can be used to independently vary the voice characteristics. Voices are selected with the commands 0O through 10O, shown in Table 2.3. Because the Voice command alters numerous internal voice parameters (articulation, pitch, expression, tone, etc.), it should precede any individual voice parameter control commands. n 0 1 2 3 4 5 6 7 8 9 10 Voice Name Perfect Paul (default) Vader Big Bob Precise Pete Ricochet Randy Biff Skip Robo Robert Goliath Alvin Gretchen Table 2.3. Voice presets * Normally used between words; duration determined by nT command. Table 2.1. DoubleTalk phoneme Symbols RC SYSTEMS articulation (na) This command adjusts the articulation level, from 0A through 9A. Excessively low articulation values tend to make the voice sound slurred; very high values, on the other hand, can make the voice sound choppy. The default articulation is 5A. RC8660 VOICE SYNTHESIZER punctuation Filter Register (nB) Depending on the application, it may be desirable to limit the reading of certain punctuation characters. For example, if the RC8660 is used to proofread documents, the application may call for only unusual punctuation to be read. On the other hand, an application that orally echoes keyboard entries for a blind user may require that all punctuation be spoken. The Punctuation Filter Register determines which punctuation characters will be spoken, and how number strings will be translated, as shown in Table 2.4. expression (e/ne) Expression, or intonation, is the variation of pitch within a sentence or phrase. When expression is enabled (n > 0), the RC8660 attempts to mimic the pitch patterns of human speech. For example, when a sentence ends with a period, the pitch drops at the end of the sentence; a question mark will cause the pitch to rise. The optional parameter n determines the degree of intonation. 0E provides no intonation (monotone), whereas 9E is very animated sounding. 5E is the default setting. If the parameter is omitted, the current (last set) value will be used. This is useful for re-enabling intonation after a Monotone command. Effect on number strings Monotone (M) When the NM bit is 0, number strings will be read one digit at a time (e.g., 0123 = "zero one two three"). Setting the NM bit to 1 forces number strings to be read as numbers (0123 = "one hundred twenty three"). Additionally, when NM = 1 and FM = 10 or 11, currency strings will be read as they are normally spoken -- for example, $11.95 will be read as "eleven dollars and ninety five cents." Setting LZS = 1 disables leading zero suppression; number strings beginning with zero will always be read one digit at a time. The default filter setting is 6B (Some punctuation, Numbers mode, leading zero suppression enabled). This command disables all intonation (expression), causing the RC8660 to speak in a monotonic voice. Intonation should be disabled whenever manual intonation is applied using the Pitch command or phoneme attribute tokens. This command is equivalent to the 0E command. Formant Frequency (nF) R 7 R 6 R 5 R 4 LZS 3 NM 2 FM 1 FM 0 This command adjusts the synthesizer's overall frequency response (vocal tract formant frequencies), over the range 0F through 99F. By varying the frequency, voice quality can be fine-tuned or voice type changed. The default frequency is 50F. Punctuation Filter Register Bits PFR.7 - 4 = RESERVED (R) Write "0" to ensure future compatibility. PFR.3 = LEADING ZERO SUPPRESSION (LZS) 1 = Do not suppress leading zeroes 0 = Suppress leading zeroes PFR.2 = NUMBERS MODE (NM) 1 = Read number strings as numbers 0 = Read number strings as digits PFR.1 - 0 = FILTER MODE (FM) 00 = All spoken 01 = Most spoken (all but CR, LF, Space) 10 = Some spoken ($%&#@=+*^|\<>) 11 = None spoken pitch (np) This command varies the synthesizer's pitch over a wide range, which can be used to change the average pitch during speech production, produce manual intonation, or create sound effects (including singing). Pitch values can range from 0P through 99P; the default is 50P. Tone (nx) The synthesizer supports three tone settings, bass (0X), normal (1X) and treble (2X), which work much like the bass and treble controls on a stereo. The best setting to use depends on the speaker being used and personal preference. Normal (1X) is the default setting. Reverb (nR) Table 2.4. punctuation Filter Register Definitions This command is used to add reverberation to the voice. 0R (the default) introduces no reverb; increasing values of n correspondingly increase the reverb delay and effect. 9R is the maximum setting. RC SYSTEMS a/D COnVeRTeR aDC Control Register (n$) This register controls the operation of the integrated analog-to-digital converter. The ADC has the following features: - - - - Four channels, 8-bit resolution (2 LSB precision) One-shot, continuous, single sweep, and continuous sweep modes of operation Selectable software or hardware triggering Support for external amplification/signal conditioning of all four ADC channels RC8660 VOICE SYNTHESIZER Figure 2.1 is a functional block diagram of the ADC input stage; Figure 2.2 illustrates the ADC in operation. Table 2.5 lists the definitions of each bit of the ADC Control Register. All ADC results are transferred via the TXD pin except in sound recorder mode -- when the results are written to the RC8660's recording memory. The default register setting is 128$. Operation of the ADC is not mutually exclusive of other RC8660 functions. The ADC can operate concurrently with text-to-speech, tone generation, audio playback, etc. The effective sampling rate in continuous mode is one-tenth the serial port baud rate (e.g., 115200 baud = 11.52 ksps). INH 7 AMP 6 TRG 5 CONT 4 SWP 3 R 2 Description CH 1 CH 0 ADC Control Register Bit ADR.7 = INHIBIT (INH) 1 = Stop A/D conversions 0 = Start A/D conversions ADR.6 = EXTERNAL AMPLIFIER (AMP) 1 = Amp connected 0 = Amp not connected ADR.5 = TRIGGER SOURCE (TRG) 1 = Hardware trigger (ADTRG pin) 0 = Software trigger ADR.4 = CONTINUOUS MODE (CONT) 1 = Continuous mode 0 = One-shot mode ADR.3 = SWEEP MODE (SWP) 1 = Sweep mode 0 = Single-channel mode ADR.2 = RESERVED (R) ADR.1 - 0 = CHANNEL SELECT (CH) When ADR.3 = 0: When ADR.3 = 1: 00 = AN0 00 = undefined 01 = AN0 - AN1 sweep 01 = AN1 10 = AN2 10 = undefined 11 = AN3 11 = AN0 - AN3 sweep This bit must be "0" in order for the ADC to begin sampling the input channel(s); setting it to "1" while the ADC is operating will cause all conversions to stop. This bit allows the other register bits to be programmed without actually starting the ADC. INH automatically changes to "1" at the end of a conversion in one-shot mode. Default: "1." Set this bit to "1" to use an operational amplifier connected between the AMPIN and AMPOUT pins. Connecting an op amp and enabling this function allows the voltage input to each ADC input pin to be amplified with one op amp. Default: "0." Setting this bit to "1" enables hardware triggering of the ADC. The ADC will not begin operating until ADR.7 is set to "0" and the ADTRG pin changes from a High to a Low level. When TRG is "0" the ADC will begin operating as soon as ADR.7 is set to "0." Default: "0." Setting this bit to "1" causes the ADC to operate continuously. If a single channel is selected for measurement (ADR.3 = 0), that channel will be read repeatedly. If sweep mode is selected (ADR.3 = 1), the active input channels will be continuously read in a cyclic fashion. Clearing this bit while the ADC is operating will stop the ADC. Default: "0." This bit determines whether a single channel or multiple input channels will be read. When Sweep mode is selected, ADR.1 and ADR.0 determine which input channels will be scanned. Default: "0." Reserved for future use. Write "0" to ensure future compatibility. These bits determine which input channel(s) will be read by the ADC. Default: "00." NOTES: 1. The AMPOUT pin can be used as a fifth ADC input if an external op amp is not used. Set ADR.6 = 1 to select the AMPOUT pin for conversion. Table 2.5. aDC Control Register Definitions RC SYSTEMS RC8660 VOICE SYNTHESIZER Figure 2.1. aDC input Block Diagram Figure 2.2. aDC Transfer Timing RC SYSTEMS Libraries of sounds and recorded messages can be stored in the RC8660's integrated recording memory for on-demand playback. New libraries can be downloaded at any time, even in the field. With the addition of a microphone and preamplifier, recordings can also be made directly to the recording memory through the RC8660's A/D converter inputs. The RC8660 includes built in support for downloading, uploading, and erasing sound files through the serial interface. The number of sound files is limited only by the amount of available on-chip recording memory. Additionally, the RC8660 can play back eight bit audio in real time, such as speech and/or sound effects stored in an external memory or file system. RC8660 VOICE SYNTHESIZER Message No_Error Invld_Cmd_Err Com_Err TmOut_Err Erase_In_Prog Erase_Err Erase_Ok Write_Err Out_Mem_Err CkSum_Err (reserved) (reserved) Incompat_Err Dup_Tag_Err Not_Found_Err Rec_In_Prog Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 No error Invalid command error Communications error Communications timeout error Memory erase in progress Memory erase error Memory erased, no errors Memory write error Out of memory Data checksum error Reserved Reserved Incompatible sound library in memory Duplicate tag in memory Record not found in memory Recording in progress Meaning ReCORDinG & playBaCk Recording Memory File System All file functions -- play, download, upload and erase -- require a means of specifying the file to be operated on. The RC8660's built-in file system allows sound files, whether downloaded or recorded through the ADC, to be easily accessed. Each sound file in memory is automatically assigned a unique record number, or index, beginning with zero. The first file is record 0, the second is record 1, and so on. Referencing a sound file by its record number is one way to select the file to be operated on. However, if files are added and/or deleted from memory frequently, their record numbers can become difficult to keep track of. All RC8660 sound files contain a unique 16 bit "tag" that can also be used to reference the file. The tag is assigned to the sound file when it is created with the RCStudio software, or, in the case of recording through the ADC, specified in the recording command. Tags can range in value from 1 to 65534. A value of 0 is defined as a null tag, and will be ignored. The setting of the TAG bit in the Protocol Options Register determines whether the tag value or record number will be used when addressing a file in the recording memory. The sound file functions described here each return one or more result codes via the TXD pin. These codes are summarized in Table 2.6. Table 2.6. Recording Memory Return Codes plays the Touch-Tone "#" key and says "hello" at the current volume setting, followed by the fourth sound file at a reduced volume level, and finally the tenth sound file at the original volume level (TAG = 0 in this example). erase Sound File (234l) The command 234Lmmmmm deletes sound file mmmmm from the recording memory. The setting of the TAG bit in the Protocol Options Register determines whether m represents a record number or tag. Note that all five m digits must be included in the command (use leading zeroes if necessary). During erasure, the CTS# pin will go High and one or more Erase_ In_Prog messages will be transmitted on the TXD pin. Completion is indicated by CTS# going Low and the transmission of Erase_Ok on the TXD pin. Note that this process can take some time, as the recording memory is also automatically defragmented during erasure. play Sound File (n&) This command plays the sound file specified by the parameter n. The setting of the TAG bit in the Protocol Options Register determines whether n represents the record number or tag value. For example, CTRL+A "52&" plays record 52 (actually the 53rd file) if TAG = 0, or the record whose tag value equals 52 if TAG = 1. The playback volume can be adjusted with the Volume (nV) command. A volume setting of 5 will cause sound files to be played back at their original volume level. Text and/or commands may be freely intermixed with the playback command. For example, CTRL+A "11*" "Hello" CTRL+A "-3V" CTRL+A "3&" CTRL+A "+3V" CTRL+A "9&" Download Sound File (236W) This command initiates the download of a sound file to the RC8660. Files are always appended to the end of the sound library in memory. RCStudio may be used to create the RC8660 compatible sound files from standard Windows wave files. After issuing this command, simply transfer the sound file. After the first dozen or so bytes of the sound file have been transferred, the RC8660 verifies that there is enough space in its recording memory and that there is not already a file in memory with the same tag (other than tag 0). No_Error will be transmitted if there are no errors, and the RC8660 will load the rest of the file. At the completion of the download, No_Error will be transmitted again (assuming no download errors). RC SYSTEMS upload Sound File (245l) This command is used to upload a sound file or recording from the RC8660's recording memory. The command 245Lmmmmm retrieves sound file mmmmm from memory; immediately upon receipt of the command, the RC8660 will begin transmitting the file via the TXD pin. The setting of the TAG bit in the Protocol Options Register determines whether m represents a record number or tag. To stop the transfer of the file, issue the Stop (CTRL+X) command. Note that all five m digits must be included in the command (use leading zeroes if necessary). The first six bytes transmitted contain information about the sound file, including its length, sampling rate/encoding type, and tag value: L24 R8 T16 where L24 is the length of the data (24 bits, least-significant byte first), R8 is the sampling rate/encoding type, and T16 is the 16-bit tag value. The lower-seven bits of R8 convey the sampling rate fs: fs = 617000/(155 - R7) Hz while the high bit specifies the encoding type: 0 = PCM, 1 = ADPCM. For example, 45h 23h 01h CEh 07h 00h indicates a sound file of 12345h bytes length, 8000 Hz sampling rate, ADPCM encoding, and a tag value of 7. The 12345h data bytes immediately follow the six-byte header. RC8660 VOICE SYNTHESIZER 99). If ADPCM compression is desired (reduces memory storage requirements by a factor of 2), add 128 to the value of n. M defines the tag value that is to be associated with the recording. If you do not want to associate a tag with the recording, set m = 00000. Note that all five m digits must be included in the command (use leading zeroes if necessary). For example, the command CTRL+A "227L01234" begins recording at 11 kHz rate with ADPCM compression, assigning a tag value of 1234 to the recording. After the command has been transmitted to the RC8660, the RC8660 will verify that there is space in the recording memory and that there is not already a file with the same tag in memory (other than tag 0). Assuming there are no errors, the RC8660 will begin recording, transmitting Rec_In_Prog every time 1024 bytes has been written to the recording memory. To stop or pause recording 1) To stop recording, issue the Stop (CTRL+X) command. The RC8660 will transmit No_Error to acknowledge it has stopped. 2) To pause recording, pull the SUSP0# pin Low. Real Time audio playback (n#/n%) Download Sound library (223W) This command is generally only found in sound libraries created with RCStudio. It initiates the download of the sound library (essentially a collection of sound files) to the RC8660. This mode allows audio samples to be written directly to the RC8660's digital-to-analog converter via the serial or parallel port. All data sent to the RC8660 is routed directly to the RC8660's internal audio buffer; the RC8660 then outputs samples from the buffer to the DAC at the rate programmed by n. Because the audio data is buffered within the RC8660, the output sampling rate is independent of the data rate into the RC8660, as long as the input rate is equal to or greater than the programmed sampling rate. The RC8660 supports PCM and ADPCM audio data formats. RC Systems' RCStudio software can convert standard Windows wave files to PCM and ADPCM formats for use with the RC8660. ADPCM compression yields data files that are half the size of PCM files, thereby reducing the required data bandwidth and storage requirements. The output sampling rate can be programmed to any rate between 4 and 11 kHz (32,000-88,000 bps) by choosing the appropriate parameter value. The relationship between the command parameter n and the sampling rate fs is n = 155 - 617/fs fs = 617/(155 - n) where fs is measured in kHz. For example, to program an 8 kHz sampling rate, choose n = 78. The range of n is 0 - 99, therefore fs can range from 4 to 11 kHz. The following procedure should be used for sending PCM or ADPCM audio data to the RC8660 in real time: NOTE If the sound file was created with RCStudio, simply transfer the file to the RC8660; the following steps should not be used. These sound files include the appropriate playback command in the header and 80h at the end of the file. However, the serial port's baud rate must be programmed for 115,200 baud in order for the data stream to be able to keep up with the RC8660. 1) Program the desired volume level with the Volume (nV) command. A volume setting of 5 will cause the data to be played back at its original volume level. This step is optional. initialize Recording Memory (214W) This command formats the RC8660's recording memory so that it can be used for storing sound files. This must be done before the initial use of the recording memory, unless a sound library has been previously downloaded, which also initializes the recording memory. The command can also be used as an "erase all files" function, if desired. During the initialization process, the CTS# pin will go High and one or more Erase_In_Prog messages (Table 2.6) will be transmitted from the TXD pin. Completion is indicated by CTS# going Low and the transmission of Erase_Ok from the TXD pin. Note that this process can take some time, depending on the size of the recording memory. Making a Recording Recording to the RC8660 requires setting up the A/D converter for the desired recording mode and issuing the Record command. To begin recording 1) Program the ADC for the desired input channel (CH), SWP = TRG = 0, and INH = 1. To record continuously, such as a voice memo, program CONT = 1. To record only 16 samples of the input channel (data logging mode), program CONT = 0. 2) Issue the Record command nLmmmmm. N programs the desired sampling rate fs, where n = 155 - 617/fs and 4 fs 11 kHz (0 n RC SYSTEMS 2) Issue the Real Time Audio Playback command n# if PCM data is being sent, or n% for ADPCM data. The RC8660 expects the audio data to immediately follow the command; therefore, be sure not to terminate the command with a CR or NUL. The TS pin and TS flag will be asserted at this time. 3) If the RC8660's serial port is being used for transferring the audio data and the port is not already running at 115,200 baud, change the host system's baud rate to 115,200 baud at this time. 4) Begin transferring the audio data to the RC8660. The same methods employed for sending any other type of data to the RC8660 should be used. Note that the DAC will not begin taking samples from the audio buffer until at least 100 bytes have been sent or the value 80h is sent, whichever occurs first. 5) After the last byte of audio data has been sent to the RC8660, send the value 80h (- 128). This signals the RC8660 to terminate Real Time Audio Playback mode and return to the text-to-speech mode of operation. Note that up to 2048 bytes of data may still be in the audio buffer, so the RC8660 may continue producing sound for as long as 0.5 second (at 4 kHz sampling rate) after the last byte of data has been sent. The TS pin/TS flag will not be cleared until all of the audio data has been output to the DAC, at which time the RC8660 will again be able to accept data from the host. If the host's serial port baud rate was changed in step 3, it should now be changed back to its original value. RC8660 VOICE SYNTHESIZER a pulse train rich in harmonic energy, which sounds more interesting than pure sinusoids in music applications. NOTE The musical tone generator output is available only from the AO pins. Digital audio output from the DAOUT pin is not possible. The musical tone generator is activated with the J command (no parameter). Once activated, all data output to the RC8660 is directed to the musical tone generator. NOTE The RC8660 expects the tone generator data to immediately follow the J command; therefore, be sure not to terminate the command with a CR or NUL. The musical tone generator is controlled with four, four-byte data and command frames, called Initialize, Voice, Play, and Quit (Figure 2.3). With these, the volume, duration, and frequencies of the three voices can be controlled. initialize Command The Initialize command sets up the tone generator's relative amplitude and tempo (speed). The host must issue this command to initialize the tone generator before sending any Voice frames. The Initialize command may, however, be issued anytime afterward to change the volume or tempo on the fly. Initialize command format The Initialize command consists of a byte of zero and three parameters. The parameters are defined as follows: KA KTL KTH Voice amplitude (1-255) Tempo, low byte (0-255) Tempo, high byte (0-255) The RC8660 contains three tone generators: musical, sinusoidal, and DTMF (Touch-Tone). TOne GeneRaTORS The musical tone generator is capable of producing three tones (voices) simultaneously, and works well in applications which require neither precise frequencies nor a "pure" (low distortion) output. The output is MuSiCal TOne GeneRaTOR The range of the tempo KT (KTL and KTH) is 1-65,535 (1 - FFFFh); the larger the value, the slower the overall speed of play. The amplitude and tempo affect all three voices, and stay in effect until another Initialize command is issued. If the command is issued between Voice frames to change the volume or tempo on the fly, only the Voice frames following the command will be affected. Figure 2.3. Musical Tone Generator Command Formats RC SYSTEMS Voice Frame Voice frames contain the duration and frequency (pitch) information for each voice. All Voice frames are stored in an 8 KB buffer within the RC8660, but are not played until the Play command is issued. If the number of Voice frames exceeds 8 KB in length, the RC8660 will automatically begin playing the data. RC8660 VOICE SYNTHESIZER For example, the Voice frame 24,64,0,0 plays Middle C using voice 1 (K1 = 64). Since K2 and K3 are zero, voices 2 and 3 will be silent during the frame. The duration of the note is a function of both the tempo KT and duration KD, which in this case is 24. As another example, 48,64,51,43 plays a C-E-G chord, for a duration twice as long as the previous example. Table 2.8 lists the recommended KD values for each of the standard musical note durations. This convention permits shorter (1/64th note) and intermediate note values to be played accurately. This is important when, for example, a thirty-second note is to be played staccato, or a note is dotted (multiplying its length by 1.5). Using the suggested values, it turns out that most musical scores sound best when played at a tempo of 255 or faster (i.e., KTH = 0). Of course, the "right" tempo is the one that sounds the best. Voice frame format Voice frames are composed of three frequency time constants (K1-K3) and a duration byte (KD), which specifies how long the three voices are to be played. The relationship between the time constant Ki and the output frequency fi is: fi = 16,768/Ki where fi is in Hertz and Ki = 4-255. Setting Ki to zero will silence voice i during the frame. KD may be programmed to any value between 1 and 255; the larger it is made, the longer the voices will play during the frame. The task of finding Ki for a particular musical note is greatly simplified by using Table 2.7. The tone generator can cover a four-octave range, from C two octaves below Middle C (Ki = 255), to D two octaves above Middle C (Ki = 14). Ki values less than 14 are not recommended. Choosing note durations and tempo Note Duration Note C C# D D# E F F# G G# A A# B C C# D D# E F F# G G# A A# B C-Mid C# Ki 255 (FFh) 241 (F1h) 228 (E4h) 215 (D7h) 203 (CBh) 192 (C0h) 181 (B5h) 171 (ABh) 161 (A1h) 152 (98h) 144 (90h) 136 (88h) 128 (80h) 121 (79h) 114 (72h) 107 (6Bh) 101 (65h) 96 (60h) 90 (5Ah) 85 (55h) 81 (51h) 76 (4Ch) 72 (48h) 68 (44h) 64 (40h) 60 (3Ch) Note D D# E F F# G G# A A# B C C# D D# E F F# G G# A A# B C C# D Ki 57 (39h) 54 (36h) 51 (33h) 48 (30h) 45 (2Dh) 43 (2Bh) 40 (28h) 38 (26h) 36 (24h) 34 (22h) 32 (20h) 30 (1Eh) 28 (1Ch) 27 (1Bh) 25 (19h) 24 (18h) 23 (17h) 21 (15h) 20 (14h) 19 (13h) 18 (12h) 17 (11h) 16 (10h) 15 (0Fh) 14 (0Eh) Whole Half Quarter Eighth Sixteenth Thirty-second 192 (C0h) 96 (60h) 48 (30h) 24 (18h) 12 (0Ch) 6 (06h) KD Table 2.8. Musical note Duration/kD Values play Command The Play command causes the voice data in the input buffer to begin playing. Additional Initialize commands and Voice frames may be sent to the RC8660 while the tone generator is operating. The TS pin and TS flag are asserted at this time, enabling the host to synchronize to the playing of the tone data. TS becomes inactive after all of the data has been played. Quit Command The Quit command marks the end of the tone data in the input buffer. The RC8660 will play the contents of the buffer up to the Quit command, then return to the text-to-speech mode that was in effect when the tone generator was activated. Once the Quit command has been issued, the RC8660 will not accept any more data until the entire buffer has been played. Table 2.7. Musical note pitch/ki Values 0 RC SYSTEMS example Tune The Basic program shown in Figure 2.4 reads tone generator data from a list of DATA statements and LPRINTs each value to the RC8660. The program assumes that the RC8660 is connected to a PC's printer port, although output could be redirected to a COM port with the DOS MODE command. RC8660 VOICE SYNTHESIZER The astute reader may have noticed some "non-standard" note durations in the DATA statements, such as the first two Voice frames in line 240. According to the original music, some voices were not to be played as long as the others during the beat. The F-C-F notes in the first frame are held for 46 counts, while the low F and C in the second frame are held for two additional counts. Adding the duration (first and fifth) bytes together, the low F and C do indeed add up to 48 counts (46 + 2), which is the standard duration of a quarter note. 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 LPRINT ' ensure serial port baud rate is locked LPRINT CHR$(1);"J"; ' activate tone generator READ B0,B1,B2,B3 ' read a frame (4 bytes) LPRINT CHR$(B0); CHR$(B1); CHR$(B2); CHR$(B3); IF B0 + B1 + B2 + B3 > 0 THEN 120 ' loop until Quit END ' ' ' Data Tables: ' ' Init (volume = 255, tempo = 86) DATA 0,255,86,0 ' ' Voice data DATA 46,48,64,192, 2,0,64,192, 48,48,0,0, 48,40,0,0, 48,36,0,0 DATA 94,24,34,0, 2,24,0,0, 24,0,36,0, 24,0,40,0, 48,0,48,0 DATA 48,40,0,192, 46,36,0,0, 2,0,0,0, 48,36,0,0, 48,24,34,0 DATA 46,24,34,0, 2,0,34,0, 46,24,34,0, 2,24,0,0, 24,0,36,0 DATA 24,0,40,0, 48,0,48,0 ' ' Play, Quit DATA 0,0,1,1, 0,0,0,0 Figure 2.4. example Musical Tone Generator program The sinusoidal tone generator generates two sinusoidal waveforms simultaneously. Applications for this generator range from generating simple, precise tones to telephone call-progress tones (such as a dial tone or busy signal). The frequency range is 0 to 4400 Hz with a resolution of 10 Hz. The sinusoidal tone generator is activated with the command nJaaaabbbb. N specifies the tone duration in 10 ms increments, between 1 and 59999. A and b specify the frequencies of generator 1 and generator 2, respectively. Note that all eight digits for a and b must be included in the command. For example, the command CTRL+A "100J03500440" generates a 350/440 Hz tone pair (a dial tone) for 1 second. SinuSOiDal TOne GeneRaTOR The DTMF (Touch-Tone) tone generator generates the 16 standard tone pairs commonly used in telephone systems. Each tone is 100 ms in duration, followed by a 100 ms inter-digit pause -- more than satisfying telephone signaling requirements (both durations can be extended to 500 ms by setting the DDUR bit of the Protocol Options Register). The DTMF generator is activated with the command n*, where n is an ASCII number between 0 and 16. The mapping of the command parameter n to the buttons on a standard telephone is shown in Table 2.9. The "pause" tone can be used to generate longer inter-digit delays in phone number strings, or to create precise silent periods in the RC8660's output. The generator's output level can be adjusted with the Volume command (nV). DTMF commands may be intermixed with text and other commands without restriction. DTMF TOne GeneRaTOR RC SYSTEMS n 0 . . 9 10 11 12 13 14 15 16 Button 0 . . 9 * # A B C D pause RC8660 VOICE SYNTHESIZER The Timeout parameter n specifies the number of 200 millisecond periods in the delay time, which can range from 200 milliseconds to 3 seconds. The default value is 0Y, which disables the timer. Sleep Timer (nQ) The sleep timer is used to force the RC8660 into Standby mode after a programmed time interval. For example, the RC8660 can power down automatically if the user forgets to turn off the power at the end of the day. An audible "reminder" tone can even be programmed to sound every ten minutes to remind the user that the power was left on, before shutdown occurs. The sleep timer is stopped and reset whenever the RC8660 is active, and begins running when the RC8660 enters Idle mode. In this way, the RC8660 will not shut itself down during normal use, as long as the programmed timer interval is longer than the maximum time the RC8660 is inactive. The command parameter n determines when Standby mode will be entered. You can place the RC8660 in Standby mode immediately, program the sleep timer to any of 15 ten-minute intervals (10 to 150 minutes), or disable the sleep timer altogether (Table 2.11). Note that the delay interval is simply n x 10 minutes for 0 < n < 16. Adding 16 to these values (16 < n < 32) also enables the reminder tone, which sounds at the end of each ten minute interval. Programming n = 0 disables the sleep timer, which is the default setting. Setting n = 16 forces the RC8660 to enter Standby mode as soon as all output has ceased. If the sleep timer is allowed to expire, the RC8660 will emit the ASCII character "p" from the TXD pin and the STBY status flag will be set to 1, just before entering Standby mode. This enables the host to detect that the RC8660 has entered Standby mode. Once the RC8660 has entered Standby mode, it can be re-awakened only by a hardware reset or by driving the STBY# pin low for 250 ns or longer, then High again. All of the RC8660 handshake signals (BUSY, CTS#, and RDY#) are forced to their "not ready" states while the RC8660 is in Standby. Table 2.9. DTMF Dialer Button Map RC8660 COnTROl Volume (nV) This is a global command that controls the RC8660's output volume level, from 0V through 9V. 0V yields the lowest possible volume; maximum volume is attained at 9V. The default volume is 5V. The Volume command can be used to set a new listening level, create emphasis in speech, or change the output level of the tone generators. Timeout Delay (ny) The RC8660 defers translating the contents of its input buffer until a CR or NUL is received. This ensures that text is spoken smoothly from word to word and that the proper intonation is given to the beginnings and endings of sentences. If text is sent to the RC8660 without a CR or NUL, it will remain untranslated in the input buffer indefinitely. The RC8660 contains a programmable timer that is able to force the RC8660 to translate its buffer contents after a preset time interval. The timer is enabled only if the Timeout Delay parameter n is non-zero, the RC8660 is not active (not talking), and the input buffer contains no CR or NUL characters. Any characters sent to the RC8660 before timeout will automatically restart the timer. n 0 n 0 1 2 . . 15 Delay Indefinite (wait for CR/NUL) 200 milliseconds 400 milliseconds . . 3000 milliseconds (3 sec.) 1 . . 15 16 17 . . 31 Sleep timer disabled 10 min . . 150 min 0 (immediate) 10 min w/reminder . . 150 min w/reminder Delay Table 2.10. Timeout Delays Table 2.11. Sleep Timer RC SYSTEMS Download exception Dictionary (247W) This command initializes the RC8660's exception dictionary and stores subsequent output from the host in the RC8660's nonvolatile dictionary memory. The maximum dictionary size is 16 KB. The creation of exception dictionaries is covered in detail in Section 3. Exception dictionaries must be compiled into the format required by the RC8660 before they can be used. The RCStudio software, available from RC Systems, includes a dictionary editor and compiler for performing this task. Dictionaries that have been compiled with RCStudio include the download command in the file header, simplifying the download process. RC8660 VOICE SYNTHESIZER 1) Write the command CTRL+A "255W". 2) Write the exact text/command sequence you want to store, up to 234 characters. For example, the string CTRL+A "3S" CTRL+A "2O" "ready" programs the RC8660 to use voice speed 3, Big Bob's voice, and say "ready" whenever it is reset. 3) Write a NUL (ASCII 00) to terminate the command and store the greeting in the RC8660's greeting memory. The RCStudio software, available from RC Systems, can create and download greeting messages for you. The 255W command and terminating NUL are embedded within the greeting message file, simplifying the download process enable exception Dictionary (u) The exception dictionary is enabled with this command. If the RC8660 is in Phoneme mode, or if an exception dictionary has not been loaded, the command will have no effect. The exception dictionary can be disabled by issuing one of the mode commands D, T, or C.). protocol Options Register (nG) Write Greeting Message (255W) Anytime the RC8660 is reset, an optional user-defined greeting message is automatically played. The message may consist of any text/command sequence up to 234 characters in length. Modal commands can be included, such as tone generator and audio playback commands. To create a new greeting message, perform the following steps: This command controls various internal RC8660 operating parameters. See Table 2.12 for the definition of each register bit. The default register setting is 144G. Bit POR.7 (V86) programs the RC8660 to emulate RC Systems' original V8600 voice synthesizer module. When this bit is set to 0, the TTS parameters and ranges are adjusted to match that of the V8600. The serial port status messages (see Table 1.3) are also affected by the setting of this bit. V86 7 SAT 6 DDUR 5 R50 4 TAG 3 R 2 Description R 1 STM 0 Protocol Options Register Bit POR.7 = V8600 COMPATIBILITY (V86) 1 = Compatibility disabled 0 = Compatibility enabled POR.6 = SATURATE (SAT) 1 = Parameters saturate 0 = Parameters wrap POR.5 = DTMF DURATION (DDUR) 1 = 500 ms 0 = 100 ms POR.4 = RC8650 COMPATIBILITY (R50) 1 = Compatibility disabled 0 = Compatibility enabled POR.3 = INDEX/TAG (TAG) 1 = Reference by tag 0 = Reference by index POR.2 - 1 = RESERVED (R) POR.0 = STATUS MESSAGES (STM) 1 = Enabled 0 = Disabled Emulates RC Systems' V8600 voice synthesizer module when set to "0." Overall voice speed range and serial port status responses are adjusted to that of the V8600. Default: "1" (in the V8600A module, this bit defaults to "0"). Determines whether command parameters wrap or saturate when their range has been exceeded. Default: "0." Determines DTMF (Touch-Tone) generator burst duration. When set to "1," tone bursts are 500 ms long; when "0," 100 ms. Default: "0." Emulates RC Systems' RC8650 chipset when set to "0." The RC8660's command set is adjusted to that of the RC8650, and RC8660-specific functions such as audio recording are disabled. Default: "1." Determines whether sound library files are referenced by their record number/index ("0") or by their tag value ("1"). Default: "0." Reserved for future use. Write "0" to ensure future compatibility. Enables and disables the transmission of certain status messages from the TXD pin. Default: "0." Table 2.12. protocol Options Register Bit Definitions RC SYSTEMS audio Control Register (nn) The Audio Control Register determines whether the RC8660's audio stream will be output as an analog signal on the AO pins or as serial digital data on the DAOUT pin. See Table 2.13 for the definition of each register bit. The default register setting is 0N. In the digital audio modes, data is transferred from the DAOUT pin in 8 bit linear, offset binary format (midscale = 80h). The DARTS# pin can be used to regulate the flow of data -- it must be Low for transfers RC8660 VOICE SYNTHESIZER to begin. In the synchronous mode, do not attempt to read the data at an average rate faster than 12 kbytes/sec (DACLK = 96 kHz). At clock rates above this, the host must pause between reading each byte in order to keep the average transfer rate from exceeding 12 kbytes/sec. Figure 2.5 illustrates the synchronous data transfer mode. Note how either DARTS# or DACLK can be used to regulate the flow of data from the RC8660. AM 7 TM 6 DPC 5 TF 4 TCP 3 BR 2 Description BR 1 BR 0 Audio Control Register Bit ACR.7 = AUDIO MODE (AM) 1 = Digital 0 = Analog ACR.6 = TRANSFER MODE (TM) 1 = Synchronous 0 = Asynchronous Set this bit to "0" to direct the audio stream to the AO pin (analog). Set the bit to "1" to direct output to the DAOUT pin (digital). Default: "0.". In the asynchronous transfer mode the data rate and timing are controlled by the internal bit rate generator (ACR.2 - 0). Data is output on the DAOUT pin and formatted as 1 start bit, 8 data bits (LSB first), and 1 stop bit. In the synchronous transfer mode the data rate and timing are controlled by the host with the DACLK pin. Data is output from the DAOUT pin as 8 bit data frames. Default: "0." ACR.5 = DAOUT PIN CONTROL (DPC) 1 = Open-drain 0 = CMOS ACR.4 = TRANSFER FORMAT (TF) 1 = MSB first 0 = LSB first ACR.3 = TRANSFER CLOCK POLARITY (TCP) 1 = Rising edge 0 = Falling edge ACR.2 - 0 = BIT RATE (BR) 000 = 2400 001 = 4800 010 = 9600 011 = 14400 100 = 19200 101 = 28800 110 = 57600 111 = 115200 Set this bit to "1" to configure the DAOUT pin as an open-drain output, or to "0" for a CMOS output. The open-drain configuration should be used when wire-or'ing two or more DAOUT pins together. Default: "0." Set this bit to "1" to have the 8 bit data frames transmitted most-significant bit first, or to "0" for least-significant bit first. Valid only in the synchronous transfer mode. Default: "0." Set this bit to "1" to clock data out of the DAOUT pin on the rising edge of the DACLK pin, or to "0" to clock data on the falling edge. Valid only in the synchronous transfer mode. Default: "0." These bits determine the bit rate used in the asynchronous transfer mode. Valid only in the asynchronous transfer mode. Default: "000." NOTES: 1. ACR.6 - ACR.0 are valid only when ACR.7 = 1. 2. ACR.4 - ACR.3 are valid only when ACR.7 and ACR.6 = 1. 3. ACR.2 - ACR.0 are valid only when ACR.7 =1 and ACR.6 = 0. Table 2.13. audio Control Register Definitions RC SYSTEMS RC8660 VOICE SYNTHESIZER Figure 2.5. Synchronous Digital audio Transfer Timing Baud Rate (nh) The serial port's baud rate can be programmed to the rates listed in Table 2.14. If included as part of the greeting message, the command will effectively override the baud rate set by the BRS pins. n 0 1 2 3 TS Mode/Polarity Automatic/Active Low Automatic/Active High Forced Low Forced High n 0 1 2 3 4 5 6 7 8 9 10 11 300 600 1200 2400 4800 9600 19200 Auto-detect 38400 57600 115200 Baud Rate Table 2.15. TS pin Control If a TS pin is programmed High or Low, it will remain so until changed otherwise. This feature can be used to activate a transmitter, for example, before speech output has begun. In the automatic mode, the TS pin is asserted as soon as output begins; it will return to its false state when all output has ceased. Note that because RC8660 commands work synchronously, the TS pin will not change state until all text and commands, up to the TS Pin Control command, have been spoken and/or executed. Stop (CTRl+x), Skip (CTRl+y) Re-read BRS3 - BRS0 pins Table 2.14. programmable Baud Rates The Stop command causes the RC8660 to stop whatever it is doing and flushes the input buffer of all text and commands. The Skip command skips to the next sentence in the buffer. Neither command affects any of the RC8660's settings. NOTE The format of these commands is unique in that the command character (CTRL+A) is not used with them. The CTRL+X (ASCII 24) and CTRL+Y (ASCII 25) characters are written directly to the RC8660, which enables the RC8660 to react immediately, even if its input buffer is full. To be most effective, the states of the RC8660 handshaking signals should be ignored. TS pin Control (nk) The TS pins provide talk status information for each audio channel, which can be used to activate a transmitter, take a telephone off hook, enable an audio power amplifier, etc., at the desired time. Each pin's state and polarity can be configured as shown in Table 2.15. The programming of the TS pins do not affect the Status Register TS flag in any way. The default setting is 1K. RC SYSTEMS zap Commands (z) This command prevents the RC8660 from honoring subsequent commands, causing it to read commands as they are encountered (useful in debugging). Any pending commands in the input buffer will still be honored. The only way to restore command recognition after the Zap command has been issued is to write CTRL+^ (ASCII 30) to the RC8660 or perform a hardware reset. RC8660 VOICE SYNTHESIZER interrogate (12?) This command retrieves the current operating settings of the RC8660. Table 2.16 lists the parameters in the order they are transmitted from the TXD pin, the command(s) that control each parameter, and each parameter's range. The parameters are organized as a byte array of one byte per parameter, with the exception of the last two parameters which are 16 bits each (low byte first). Reinitialize (@) This command reinitializes the RC8660 by clearing the input buffer and restoring the voice parameters and control registers to their factory default settings. The exception dictionary, recording memory, greeting message, baud rate, nor TS pin control setting are affected. Parameter Mode PFR register Formant freq Pitch Speed Volume Tone Expression Dict loaded Dict status Input buffer capacity Articulation Reverb TS pin control POR register ACR register Rec memory capacity Sleep delay Timeout delay Char mode delay Text mode delay Voice ADR register Free recording memory (16 bits) # of files in recording memory (16 bits) Cmd C/D/T nB nF nP nS nV nX nE 247W C/T/U - nA nR nK nG nN - nQ nY nC nT nO n$ - - Range 0=Char; 1=Phon; 2=Text 0-15 0-99 0-99 0-13 0-9 0-2 0-9 0=not loaded; 1=loaded 0=disabled; 1=enabled x256 bytes 0-9 0-9 0-3 0-255 0-255 x16K bytes 0-31 0-15 0-31 0-15 0-10 0-255 x256 bytes 0-999 MiSCellaneOuS FunCTiOnS index Marker (ni) Index markers are nonspeaking "bookmarks" that can be used to keep track of where the RC8660 is reading within a passage of text. The parameter n is any number between 0 and 255; thus, up to 256 unique markers may be active at any given time. When the RC8660 has spoken the text up to a marker, it transmits the marker number to the host via the TXD pin. Note that this value is a binary number between 0 and 255, not a literal ASCII number string as was used in the command to place the marker. This allows the marker to be transmitted as a one-byte value. There is no limitation to how many index markers can be used in a text string. The frequency depends on the resolution required by the application. In Text mode, for example, one marker per sentence or one marker per word would normally be used. In Phoneme mode, markers can be placed before each phoneme to monitor phoneme production, which is useful for synchronizing an animated mouth with the voice. Markers may also be placed with tone generation and recorded audio playback commands, if desired. Chipset identification (6?) This command returns RC8660 system information that is used during factory testing. Eight bytes are transmitted via the TXD pin. The only information that may be of relevance to an application is the internal microcode revision number, which is conveyed in the last two bytes in packed-BCD format. For example, 41h 02h would be returned if the version number was 2.41. Table 2.16. parameters Returned by interrogate Command RC SYSTEMS COMManD SuMMaRy Command nA nB C/nC D E/nE nF nG nH nI J nJ nK nL 234L 245L M nN nO nP nQ nR nS T/nT U nV 214W 223W 236W 247W 255W nX nY Z @ n* n#/n% n& n$ n? CTRL+X/Y Articulation Punctuation Filter Register Character mode Phoneme mode Expression Formant frequency Protocol Options Register Baud rate Index marker Musical tone generators Sinusoidal tone generators TS pin control Record * Erase sound file * Upload sound file * Monotone Audio Control Register * Voice Pitch Sleep timer Reverb Speed Text mode/delay Enable exception dictionary Volume Initialize recording memory * Download sound library * Download sound file * Download exception dictionary * Write greeting message * Tone Timeout delay Zap commands Reinitialize DTMF generator Real time audio playback * Play sound file ADC Control Register Chipset ID/Interrogate * Stop/Skip Function RC8660 VOICE SYNTHESIZER n Range 0-9 0-15 0-31 - 0-9 0-99 0-255 0-11 0-255 - 1-59999 0-3 0-227 234 245 - 0-255 0-10 0-99 0-31 0-9 0-13 0-15 - 0-9 214 223 236 247 255 0-2 0-15 - - 0-16 0-99 0-65534 0-255 6/12 - Default n 5 6 0 - 5 50 144 BRS pins - - - 1 - - - - 0 0 50 0 0 5 0 - 5 - - - - - 1 0 - - - - - 128 - - * Cannot be used in greeting messages. Table 2.17. RC8660 Command Summary RC SYSTEMS RC8660 VOICE SYNTHESIZER Section 3: exception DictionarieS Exception dictionaries make it possible to alter the way the RC8660 interprets character strings it receives. This is useful for correcting mispronounced words, triggering the generation of tones and/or the playback of pre-recorded sounds, or even speaking in a foreign language. In some cases, an exception dictionary may even negate the need of a text pre-processor in applications that cannot provide standard text strings. This section describes how to create exception dictionaries for the RC8660. The text-to-speech modes of the RC8660 utilize an English lexicon and letter-to-sound rules to convert text the RC8660 receives into speech. The pronunciation rules determine which sounds, or phonemes, each character will receive based on its relative position within each word. The integrated DoubleTalk text-to-speech engine analyzes text by applying these rules to each word or character, depending on the operating mode in use. Exception dictionaries augment this process by defining exceptions for (or even replacing) these built in rules. Exception dictionaries can be created and edited with a word processor or text editor that stores documents as standard text (ASCII) files. However, the dictionary must be compiled into the internal format used by the RC8660 before it can be used. The RCStudio software, available from RC Systems, includes a dictionary editor and compiler. Symbol # + ^ * : ? @ ! % Definition A vowel: a, e, i, o, u, y A front vowel: e, i, y A consonant: b, c, d, f, g, h, j, k, l, m, n, p, q, r, s, t, v, w, x, z One or more consonants Zero or more consonants A voiced consonant: b, d, g, j, l, m, n, r, v, w, z One of: d, j, l, n, r, s, t, z, ch, sh, th One of: b, c, d, f, g, p, t A suffix: able(s), ably, e(s), ed(ly), er(s), ely, eless, ement(s), eness, ing(s), ingly (must also be followed by a non- alphabetic character) A sibilant: c, g, j, s, x, z, ch, sh A nonalphabetic character (number, space, etc.) One or more non-printing characters (spaces, controls, line breaks, etc.) A digit: 0-9 One or more digits Wildcard (matches any character) & $ ~ \ | Exceptions have the general form L(F)R=P which means "the text fragment F, occurring with left context L and right context R, gets the pronunciation P." All three parts of the exception to the left of the equality sign must be satisfied before the text fragment will receive the pronunciation given by the right side of the exception. The text fragment defines the input characters that are to be translated by the exception, and may consist of any combination of letters, numbers, and symbols. Empty (null) text fragments may be used to generate sound based on a particular input pattern, without actually translating any of the input text. The text fragment (if any) must always be contained within parentheses. Characters to the left of the text fragment specify the left context (what must come before the text fragment in the input string), and characters to the right define the right context. Both contexts are optional, so an exception may contain neither, either, or both contexts. There are also 15 special symbols, or context tokens, that can be used in an exception's context definitions (Table 3.1). Note that although context tokens are, by definition, valid only within the left and right context definitions, the wildcard token may also be used within text fragments. Any other context token appearing within a text fragment will be treated as a literal character. exCepTiOn SynTax Table 3.1. Context Tokens The right side of an exception (P) specifies the pronunciation that the text fragment is to receive, which may consist of any combination of phonemes (Table 2.1), phoneme attribute tokens (Table 2.2), and commands (Table 2.17). Using the tone generator and pre-recorded audio playback commands, virtually limitless combinations of speech, tones, and sound effects can be triggered from any input text pattern. If no pronunciation is given, no sound will be given to the text fragment; the text fragment will be silent. A dictionary file may also contain comments, but they must be on lines by themselves (i.e., they cannot be on the same line as an exception). Comment lines must begin with a semicolon character (;), so the compiler will know to skip over them. An example of an exception is C(O)N=AA which states that o after c and before n gets the pronunciation AA, the o-sound in cot. For example, the o in conference, economy, and icon would be pronounced according to this exception. RC SYSTEMS Another example is $R(H)= which states that h after initial r is silent, as in the word rhyme (the $ context token represents any non-alphabetic character, such as a space between words; see Table 3.1). Punctuation, numbers, and most other characters can be redefined with exceptions as well: (5)=S I NG K O (CHR$)=K EH R IX K T ER (Spanish five) (Basic function) RC8660 VOICE SYNTHESIZER (O)+=OW (O)=UW The first exception states that o followed by e, i, or y is to be pronounced OW, the o-sound in boat. The second exception does not place any restriction on what must come before or after o, so o in any context will receive the UW pronunciation. If the exceptions were reversed, the (O)+ exception would never be reached because the (O) exception will always match o in any context. In general, tightly-defined exceptions (those containing many context restrictions) should precede loosely-defined exceptions (those with little or no context definitions). (RAT)=R AE T (RATING)=R EY T IH NG (R)=R This is an example of how not to organize exceptions. The exception (RATING) will never be used because (RAT) will always match first. According to these exceptions, the word rating would be pronounced "rat-ing." It can be beneficial to group exceptions by the first character of the text fragments, that is, all of the A exceptions in one group, all the B exceptions in a second group, and so on. This gives an overall cleaner appearance, and can prove to be helpful if the need arises to troubleshoot any problems in your dictionary. In order to better understand how an exception dictionary works, it is helpful to understand how the DoubleTalk text-to-speech engine processes text. Algorithms within the DoubleTalk engine analyze input text a character at a time, from left to right. A list of pronunciation rules is searched sequentially for each character until a rule is found that matches the character in the correct position and context. The algorithm then passes over the input character(s) bracketed in the rule (the text fragment), and assigns the pronunciation given by the right side of the rule to them. This process continues until all of the input text has been converted to phonetic sounds. The following example illustrates how the algorithm works by translating the word receive. The algorithm begins with the letter r and searches the R pronunciation rules for a match. The first rule that matches is $(RE)^#=R IX, because the r in receive is an initial r and is followed by an e, a consonant (c), and a vowel (e). Consequently, the text fragment re receives the pronunciation R IH, and the scan moves past re to the next character: receive. (E is not the next scan character because it occurred inside the parentheses with the r; the text fragment re as a whole receives the pronunciation R IX) The first match among the C rules is (C)+=S, because c is followed by an e, i, or y. C thus receives the pronunciation S, and processing continues with the second e: receive. (EI)=IY is the first rule to match the second e, so ei receives the sound IY. Processing resumes at the character receive, which matches the default V rule, (V)=V. The final e matches the rule #:(E)$=, which applies when e is final and follows zero or more consonants and a vowel. Consequently, e receives no sound and processing continues with the following word or punctuation, if any. Thus, the entire phoneme string for the word receive is R IX S IY V. The TRanSlaTiOn alGORiThM It is possible that some input text may not match anything in a dictionary, depending on the nature of the dictionary. For example, if a dictionary was written to handle unusual words, only those words would be included in the dictionary. On the other hand, if a dictionary defined the pronunciation for another language, it would be comprehensive enough to handle all types of input. In any case, if an exception is not found for a particular character, the English pronunciation will be given to that character according to the built in pronunciation rules. Generally, the automatic switchover to the built in rules is desirable if the dictionary is used to correct mispronounced words, since by definition the dictionary is defining exceptions to the built in rules. If the automatic switchover is not desired, however, there are two ways to prevent it from occurring. One way is to end each group of exceptions with an unconditional exception that matches any context. For example, to ensure that the letter "a" will always be matched, end the A exception group with the exception (A)=pronunciation. This technique works well to ensure matches for specific characters, such as certain letters or numbers. If the exception dictionary is to replace the built in rules entirely, end the dictionary with the following exception: ()= TexT nOT MaTCheD By The DiCTiOnaRy Since DoubleTalk uses its translation rules in a sequential manner, the position of each exception relative to the others must be carefully considered. For example, consider the following pair of exceptions: Rule pReCeDenCe This special exception causes unmatched characters to be ignored (receive no sound), rather than receive the pronunciation defined by the built in rules. RC SYSTEMS Punctuation defined in the exception dictionary has priority over the Punctuation Filter command. Any punctuation defined in the dictionary will be used, regardless of the Punctuation Filter setting. NOTE If the dollar sign character ($) is defined within the text fragment of any exception, currency strings will not be read as dollars and cents. RC8660 VOICE SYNTHESIZER When zero isn't Really zero When reading addresses or lists of numbers, the word "oh" is often substituted for the digit 0. For example, we might say 1020 North Eastlake as "one oh two oh North Eastlake." The digit 0 can be redefined in this manner with the following exception: (0)=OW eFFeCT On punCTuaTiOn acronyms and abbreviations Exceptions are defined independently for the Character and Text modes of operation. The beginning of the Character mode exceptions is defined by inserting the letter C just before the first Character mode exception. No exceptions prior to this marker will be used when the RC8660 is in Character mode, nor will any exceptions past the marker be used in Text mode. For example: . . ()= (Text mode exceptions) (optional; used if built in rules are not to be used in no-match situations) (Character mode exceptions marker) (Character mode exceptions) (optional; used if built in rules are not to be used in no-match situations) ChaRaCTeR MODe exCepTiOnS Acronyms and abbreviations can be defined so the words they represent will be spoken. $(KW)$=K IH L AH W AA T $(DR)$=D AA K T ER $(TV)$=T EH L AX V IH ZH IX N String parsing & Decryption Sometimes the data that we would like to have read is not available in a "ready-to-read" format. For example, the output of a GPS receiver may look something like this: $GPGGA,123456,2015.2607,N,... The first 14 characters of the string consists of a fixed header and variable time data, which we would like to discard. The following exception ensures that the header will not be read: ($GPGGA,,)= Note how wildcard tokens are used for handling the time data (8th - 13th characters), since the content of this field is variable. The 15th - 16th and 17th - 18th characters represent the latitudinal coordinate in degrees and minutes, respectively. The three exceptions shown below handle the latitudinal component of the GPS string. Note in the first exception how a null text fragment is used in the appropriate position to generate the word "degrees," without actually translating any of the input characters. ,\\()\\.=D IX G R IY Z , , (.)=M IH N IH T S , , (,N,)=N OW R TH L AE T IH T UW D The four exceptions together will translate the example string as "20 degrees, 15 minutes, north latitude." (Additional exceptions for handling the seconds component, and digits themselves, are not shown for clarity). C . . . ()= The following examples illustrate some ways in which the exception dictionary can be used. appliCaTiOnS Correcting Mispronounced Words Correcting mispronounced words is the most common application for exception dictionaries. S(EAR)CH=ER $(OK)$=OW K EY The first exception corrects the pronunciation of all words containing search (search, searched, research, etc.). As this exception illustrates, it is only necessary to define the problem word in its root form, and only the part of the word that is mispronounced (ear, in this case). The second exception corrects the word ok, but because of the left and right contexts, will not cause other words (joke, look, etc.) to be incorrectly translated. heteronyms no Cussing, please The reading of specific characters or words can be suppressed by writing exceptions in which an alternate pronunciation is given. (????)= (YOU fill in the blanks!) (????)=CTRL+A 30j10000000 The first example simply says nothing when the defined word is encountered, whereas a 1 kHz tone is played in the second example. Heteronyms are words that have similar spellings but are pronounced differently, depending on the context, such as read ("reed" and "red") and wind ("the wind blew" and "wind the clock"). Exceptions can be used to fix up these ambiguities, by including non-printing (Control) characters in the text fragment of the exception. Suppose a line of text required the word "close" to be pronounced as it is in "a close call," instead of as in "close the window." The following exception changes the way the s will sound: (CTRL+D CLOSE)=K L OW S 0 RC SYSTEMS Note the CTRL+D character (ASCII code 04) in the text fragment. CTRL+D is a non-printing character, but the translation algorithms treat it as they would any printing character. Thus, the string "CTRL+D close" will be pronounced with the s receiving the "s" sound. "Close" without the CTRL+D will be unaffected -- the s will still receive the "z" sound. It does not matter where you place the Control character in the word, as long as you use it the same way in your application's text. You may use any non-printing character (except LF and CR) in this manner. RC8660 VOICE SYNTHESIZER For example, by connecting the four control bits to DB0 through DB3, DB4 and DB5 to VCC, DB6 and DB7 to ground and the strobe to WR#, ASCII codes 30h through 3Fh (corresponding to the digits "0" through "9" and the six ASCII characters following them) can be generated by the four control bits. Message strings would then be assigned to each of these ASCII characters. For example, you could make the character "0" (corresponding to all four control bits = 0) say, "please insert quarter," with the following dictionary entry: (0)=P L IY Z IH N S ER T K W OW R T ER non-english languages Dictionaries can be created that enable the RC8660 to speak in languages other than English. It's not as difficult as it may seem -- in most cases all that is required is a pronunciation guide and a bit of patience. If you don't have a pronunciation guide for the language you're interested in, check your local library. Most libraries have dictionaries for other languages that include pronunciation guides, which make it easy to transcribe the pronunciation rules into exception form. A good example of an exception dictionary for the Spanish language is included with RCStudio. The Timeout timer should also be activated (1Y, for example) in order for the "message" to be executed. Otherwise, the RC8660 will wait indefinitely for a CR/NUL character that will never come. The timer command could be included in the greeting message. Make sure that your exceptions aren't so broad in nature that they do more harm than good. Exceptions intended to fix broad classes of words, such as word endings, are particularly notorious for ruining otherwise correctly pronounced words. Take care in how your exceptions are organized. Remember, an exception's position relative to others is just as important as the content of the exception itself. TipS language Translation Exception dictionaries even allow text written in one language to be read by the RC8660 in yet another language, as long as the vocabulary is limited. The following exceptions demonstrate how this can be done with three example Spanish/English words. (GRANDE)=L AA R J (BIEN)=F AY N (USTED)=YY UW The sense of translation can also be reversed: (LARGE)=G RR A N D EI (FINE)=B I EI N (YOU)=U S T EI DH When Things Don't Work as expected On rare occasions, an exception may not work as expected. This occurs when the built in pronunciation rules get control before the exception does. The following example illustrates how this can happen. Suppose an exception redefined the o in the word "process" to have the long "oh" sound, the way it is pronounced in many parts of Canada. Since the word is otherwise pronounced correctly, the exception redefines only the "o:" PR(O)CESS=OW Message Macros Certain applications may not be able to send text strings to the RC8660. An example of such an application is one that is only able to output a four bit control word and strobe. Sixteen unique output combinations are possible, but this is scarcely enough to represent the entire ASCII character set. You can, however, assign an entire spoken phrase to a single ASCII character with the exception dictionary. By driving four of the data bus lines of the bus interface (see Figure 1.7) and hardwiring the remaining four to the appropriate logic levels, virtually any set of 16 ASCII characters can be generated, which in turn can be interpreted by the exception dictionary. But much to our horror, the RC8660 simply refuses to take on the new Canadian accent. It so happens that the RC8660 has a built in rule which looks something like this: $(PRO)=P R AA This rule translates a group of three characters, instead of only one as most of the built in rules do. Because the text fragment PRO is translated as a group, the o is processed along with the initial "pr," and consequently the exception never gets a shot at the o. If you suspect this may be happening with one of your exceptions, include more of the left-hand side of the word in the text fragment (in the example above, (PRO)CESS=P R OW would work). RC SYSTEMS RC8660 VOICE SYNTHESIZER Section 4: rc8660 evaluation Kit The RC8660 Evaluation Kit comes with everything required to evaluate and develop applications for the RC8660 chipset using a Windowsbased PC. The included RCStudioTM software provides an integrated development environment with the following features: * * * * Read any text, either typed or from a file Easy access to the various RC8660 voice controls Manage collections of sound files and store them in the RC8660 Exception dictionary editor/compiler, and much more... The following components are included in the DoubleTalk RC8660 Evaluation Kit: * * * * * Printed circuit board containing the RC8660-1 chipset AC power supply Speaker Serial cable RCStudioTM development software CD eValuaTiOn kiT COnTenTS The evaluation board can also be used in stand-alone environments by simply printing the desired text and commands to it via the onboard RS-232 serial or parallel ports. eVal BOaRD OuTline RC SYSTEMS COnneCTOR pin aSSiGnMenTS & SCheMaTiCS Pin No. 1 2 3 4 5 6 7 8 Pin Name AO0 AO1 SP+0 SP+1 SP-0 SP-1 TS0 TS1 Pin No. 9 10 11 12 13 14 15 16 Pin Name AS0 AS1 SUSP0 SUSP1 DAOUT DARTS DACLK GND RC8660 VOICE SYNTHESIZER Pin No. 1 2 3 4 5 Pin Name NC RXD TXD NC GND Pin No. 6 7 8 9 - Pin Name DSR RTS CTS NC - Table 4.4. p101 pin assignments (RS-232 Serial interface) Table 4.1. p1 pin assignments (audio Output & Control) Pin No. 1 2 Pin Name GND CTS Pin No. 3 4 Pin Name TXD RXD Pin No. 1 2 3 4 5 Pin Name AN0 GND AN1 GND AN2 Pin No. 6 7 8 9 10 Pin Name GND AN3 GND ADTRG GND Note: JP5-JP7 must be open in order to use the TTL interface Table 4.5. p102 pin assignments (TTl Serial interface) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Pin Name STB# AFD# DATA0 ERROR# DATA1 INIT# DATA2 SLCTIN# DATA3 GND DATA4 GND DATA5 Pin No. 14 15 16 17 18 19 20 21 22 23 24 25 26 Pin Name GND DATA6 GND DATA7 GND ACK# GND BUSY GND PE GND SLCT RD# Table 4.2. p2 pin assignments (a/D Converter) JP4 X X X X X X X X JP3 X X X X JP2 X X JP1 X X Baud Rate 300 600 1200 2400 4800 9600 19200 Auto-detect 38400 57600 115200 Auto-detect Auto-detect Auto-detect Auto-detect Auto-detect (default) X X X X X X X X X X X X Table 4.6. p103 pin assignments (printer/Bus interface) X X X X Table 4.3. Jp1-Jp4 Jumper assignments (Baud Rate) RC SYSTEMS RC8660 VOICE SYNTHESIZER RC SYSTEMS RC8660 VOICE SYNTHESIZER RC SYSTEMS RC8660 VOICE SYNTHESIZER RC SYSTEMS RC8660 VOICE SYNTHESIZER RC SYSTEMS RC8660 VOICE SYNTHESIZER Section 5: compatibility With the rc8650 Item I/O Pins RC8660 Pin 11 BRS3: Fourth baud rate select pin Pin 38 CTS#: Goes High only when there is data in the internal serial port overrun buffer NC: No connection RC8650 CTS#: Pulses High after each byte received SEL pins not supported (connect to Low level) 2 KB Downloading of Greeting message erases exception dictionary (dictionary must be reloaded) 0 - 910 seconds recording time No internal file system (entire sound library must be re-downloaded for changes to take effect) Not supported L 0 - 9F (5F) 0 - 9S (1S) 0 - 7O (0O) 0 - 99I Pins 10, 89 - 92 SEL pins fully support multi-channel applications Memory Input buffer 8 KB Greeting message Downloading of Greeting message does not affect exception dictionary Recording memory 130 - 910 seconds recording time Internal file system allows individual sound files to be added and deleted in the field Record voice and analog data via ADC input pins; play back and/or upload recordings via serial port Commands Load Dictionary 247W Formant Freq 0 - 99F (50F) Speed 0 - 13S (5S) Voice 0 - 11O (0O) Index Marker 0 - 255I Interrogate (12?) Returns same information as RC8650, plus free space available and # of files in recording memory Sinusoidal tone 0 - 4400 Hz frequency range; 10 ms - 600 sec generator duration range; simplified command syntax Data File Compatibility Greeting messages Compatible with RC8650 greeting files Dictionaries Compatible with RC8650 dictionary files Sound libraries Compatible with RC8650 and RC8660 library files, but internal RC8660 file system is compatible only with RC8660 libraries Sound files Can play both RC8650 and RC8660 sound files in real time playback mode, but POR.4 must be set to "0" to play RC8650 ADPCM-encoded files. Internal RC8660 file system is compatible only with RC8660 sound files when used in sound libraries 0 - 2746 Hz frequency range; 23 ms - 16.5 sec duration range Compatible with RC8650 library files only; individual sound file changes can be done only by downloading the new library file in its entirety Compatible with RC8650 sound files only In RC8650 Compatibility mode (POR.4 = "0"), the RC8660 uses the RC8650 command ranges and defaults. Specifications written in this publication are believed to be accurate, but are not guaranteed to be entirely free of error. RC Systems reserves the right to make changes in the devices or the device specifications described in this publication without notice. RC Systems advises its customers to obtain the latest version of device specifications to verify, before placing orders, that the information being relied upon by the customer is current. In the absence of written agreement to the contrary, RC Systems assumes no liability relating to the sale and/or use of RC Systems products including fitness for a particular purpose, merchantability, for RC Systems applications assistance, customer's product design, or infringement of patents or copyrights of third parties by or arising from use of devices described herein. Nor does RC Systems warrant or represent that any license, either express or implied, is granted under any patent right, copyright, or other intellectual property right of RC Systems covering or relating to any combination, machine, or process in which such devices might be or are used. RC Systems products are not intended for use in medical, life saving, or life sustaining applications. Applications described in this publication are for illustrative purposes only, and RC Systems makes no warranties or representations that the devices described herein will be suitable for such applications. 1609 england avenue, everett, Wa 98203 phone: (425) 355-3800 Fax: (425) 355-1098 http://www.rcsys.com |
Price & Availability of RC86L60-3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |